Lexmark C530DN Technical Reference - Page 184

Table 3-22, Variables for Flash and Disk File and Password Commands

Page 184 highlights

3-87 PJL Table 3-22 lists the parameters used with most of the commands. Additional parameters are noted in the description of each command. Table 3-22: Variables for Flash and Disk File and Password Commands Parameter accesstype bytecount Syntax ACCESS = accesstype LENGTH = bytecount Description One of the following access types must be specified when a file is opened: RO Open for read only. The file must already exist on the specified device. WO Create a new file. If the file already exists, its contents will be discarded and a new file will be created. RW Open for reading and writing. The file must already exist. AP Open for reading and writing, and position the file pointer to the end of the file. The file must already exist. Access types are case sensitive. The LREADFILE command is ignored if the file was not opened with an accesstype of RO, RW, or AP. The LWRITEFILE command is ignored if the file was not opened with an accesstype of WO, RW, or AP. The amount of data in bytes to be read or written. The parameter is optional for both the LREADFILE and LWRITEFILE commands. If the LENGTH parameter is omitted from the LREADFILE command, bytecount is assumed to be equal to the entire file beginning at the START location. If the LENGTH parameter is omitted from the LWRITEFILE command, an @PJL END DATA command must be placed at the end of the data. All data up to '@' in @PJL END DATA is written to the file. Note: The LWRITEFILE command requires that either the LENGTH parameter or the @PJL END DATA command be specified, but not both. If the LENGTH is greater than the file size on a LREADFILE command, it is assumed to be the entire file beginning at the START location.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246
  • 247
  • 248
  • 249
  • 250
  • 251
  • 252
  • 253
  • 254
  • 255
  • 256
  • 257
  • 258
  • 259
  • 260
  • 261
  • 262
  • 263
  • 264
  • 265
  • 266
  • 267
  • 268
  • 269
  • 270
  • 271
  • 272
  • 273
  • 274
  • 275
  • 276
  • 277
  • 278
  • 279
  • 280
  • 281
  • 282
  • 283
  • 284
  • 285
  • 286
  • 287
  • 288
  • 289
  • 290
  • 291
  • 292
  • 293
  • 294
  • 295
  • 296
  • 297
  • 298
  • 299
  • 300
  • 301
  • 302
  • 303
  • 304
  • 305
  • 306
  • 307
  • 308
  • 309
  • 310
  • 311
  • 312
  • 313
  • 314
  • 315
  • 316
  • 317
  • 318
  • 319
  • 320
  • 321
  • 322
  • 323
  • 324
  • 325
  • 326
  • 327
  • 328
  • 329
  • 330
  • 331
  • 332
  • 333
  • 334
  • 335
  • 336
  • 337
  • 338
  • 339
  • 340
  • 341
  • 342
  • 343
  • 344
  • 345
  • 346
  • 347
  • 348
  • 349
  • 350
  • 351
  • 352
  • 353
  • 354
  • 355
  • 356
  • 357
  • 358
  • 359
  • 360
  • 361
  • 362
  • 363
  • 364
  • 365
  • 366
  • 367
  • 368
  • 369
  • 370
  • 371
  • 372
  • 373
  • 374
  • 375
  • 376
  • 377
  • 378
  • 379
  • 380
  • 381
  • 382
  • 383
  • 384
  • 385
  • 386
  • 387
  • 388
  • 389
  • 390
  • 391
  • 392
  • 393
  • 394
  • 395
  • 396
  • 397
  • 398
  • 399
  • 400
  • 401
  • 402
  • 403
  • 404
  • 405
  • 406
  • 407
  • 408
  • 409
  • 410
  • 411
  • 412
  • 413
  • 414
  • 415
  • 416
  • 417
  • 418
  • 419
  • 420
  • 421
  • 422
  • 423
  • 424
  • 425
  • 426
  • 427
  • 428
  • 429
  • 430
  • 431
  • 432
  • 433
  • 434
  • 435

PJL
3-87
Table 3-22 lists the parameters used with most of the commands. Additional
parameters are noted in the description of each command.
Table 3-22:
Variables for Flash and Disk File and Password Commands
Parameter
Syntax
Description
accesstype
ACCESS =
accesstype
One of the following access types must be specified when a file is opened:
RO
Open for read only. The file must already exist on the specified
device.
WO
Create a new file. If the file already exists, its contents will be
discarded and a new file will be created.
RW
Open for reading and writing. The file must already exist.
AP
Open for reading and writing, and position the file pointer to the end
of the file. The file must already exist.
Access types are case sensitive.
The LREADFILE command is ignored if the file was not opened with an
accesstype
of
RO
,
RW
, or
AP
. The LWRITEFILE command is ignored if the
file was not opened with an
accesstype
of
WO
,
RW
, or
AP
.
bytecount
LENGTH =
bytecount
The amount of data in bytes to be read or written. The parameter is optional
for both the LREADFILE and LWRITEFILE commands.
If the LENGTH parameter is omitted from the LREADFILE command,
bytecount
is assumed to be equal to the entire file beginning at the START
location. If the LENGTH parameter is omitted from the LWRITEFILE
command, an @PJL END DATA command must be placed at the
end
of the
data. All data up to ‘@’ in @PJL END DATA is written to the file.
Note:
The LWRITEFILE command requires that
either
the LENGTH
parameter or the @PJL END DATA command be specified, but not both.
If the LENGTH is greater than the file size on a LREADFILE command, it is
assumed to be the entire file beginning at the START location.