Marantz SR5002 SR4002_Rear_Panel_Drawing - Page 24
Connecting Hdmi Components - protect
View all Marantz SR5002 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 24 highlights
ENGLISH CONNECTING HDMI COMPONENTS HDMI JACK This unit has 3 HDMI inputs and one HDMI output. It can send digital video and audio signals from DVDs and other sources directly to a display. It minimizes signal degradation caused by analog conversion so that high quality images can be enjoyed. Select an input source from the OSD menu system. (See page 27) Notes: • When the HDMI output is connected to a display monitor that does not support HDCP*, signals are not output. To view images in HDMI, it is necessary to connect to a display that supports HDCP*. • There may be no image output if connected to a TV or display that is not compatible with the above format. • Refer to the instruction manual of the TV or display to be connected to the unit for detailed information regarding the HDMI terminal. * HDCP: High-bandwidth Digital Content Protection CONNECTING HDMI COMPONENTS An HDMI cable (sold separately) is used to connect the HDMI jack on the unit with the HDMI jack on a DVD player, TV, projector or other component. To transmit multichannel audio via HDMI, the connected player must support multichannel audio transmission through its HDMI jack. HDMI video streaming is compatible with DVI in principle. Therefore, it is possible to connect to a TV or monitor that has a DVI terminal using an HDMI-DVI conversion cable or plug. When connecting to a DVI terminal, connect the audio signal separately. Notes: • Some HDMI components can be controlled over the HDMI cable, but this unit cannot control other components this way. • When connected to a monitor (i.e., TV, projector, etc.) that does not support HDCP, video and audio are not output. • DVI cables come with 24-pin and 29-pin plugs. This unit supports 24-pin DVI-D cables; 29-pin DVI cables cannot connect to it. • Some source devices such as DVD players does not support HDMI repeater like those of the unit. In such case, pictures are not properly projected on monitors such as TVs and projectors. DVD player VIDEO PROJECTOR • When multiple components are connected to this unit, turn power to unused components off to prevent interference between them. HDMI OUTPUT HDMI INPUT • Disconnecting or connecting cables with the power on can damage the equipment. Turn the power off before disconnecting or connecting cables. • Some DVD-Audio disks disable downmixing. These types of disks are not played back correctly unless the left, center, right and surround left and right speakers, and subwoofer are connected. • If a DVD player that does not support HDMI 1.1 is INPUT 1 VIDEO connected to the unit, multi channel PCM playback COMPONENT INPUT 3 VIDEO is not possible even with DVD-Audio disks.S-VIDEO FM (75) GND AM MONITOR 1 OUT 2 ANTENNA INPUT • If a DVD player or other device with DVI output is L SL C SBL TV DVD VCR IN VCR OUT DSS MONITOR OUT 2 Y CB/PB CR/PR Y CB/PB CR/PR Y CB/PB CR/PR IN INPUT 1 connected to the unit, a sepaL rate audio cable (optical- 4 5 digital, coaxial digital or analog) is needed for the R audio signals. In this case, select the connected audio R SR SW SBR MULTI. input as explained in "1 INPUT (AUX2) SETUP". 7.1CH INPUT (SeOeUTpagTVe DVD IN OUT VCR DSS IN OUT TAPE AUDIO 1 IN OUT CD/CDR 2 3 DIGITAL IN OPT OUT DIGITAL OUT REMOTE CONT. FLASHER DC IN TRIGGER 27) RS-232C SPEAKER C OFF ON INPUT 2 HDMI Ver 1.1 INPUT 3 XM OUTPUT • Multi channel PCM signals aLnd aSLudioC sigSBnLals of 64 AC IN kHz or higher that are input from the HDMI jack arRe L R L R L R L not output from the DIGITAL OUT jacks. • Depending on the quiality of the cable used, theFRONT B R SR SW SBR FRONT A OR B.CENTER. HDMI signal may be affected byPnREoOisUeT . FRONT A + B : 8 OHMS • Audio units that use sampling frequencies of 128 kHz and above are not supported. FRONT A SURROUND BACK SURROUND SPEAKER C/MULTI SPEAKER SURR.SURR BACK : 6-8 OHMS CENTER SPEAKER SYSTEMS SWITCHED 1.25A 150W AC OUTLETS 120V 60Hz MODEL NO. SR5002 • When only HDMI components are connected, OSD will not be displayed. (See page 26) Satellite Tuner HDMI OUTPUT 21