Marantz SR5002 SR4002_Rear_Panel_Drawing - Page 46
Marantz SR5002 Manual
View all Marantz SR5002 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 46 highlights
ENGLISH (Using the remote controller) 1. Tune into the radio station you desire (Refer to the "MANUAL TUNING" or "AUTO TUNING" section). 2. Press the MEMO button on the remote controller. "- -" (preset number) starts blinking on the display. 3. Enter the desired preset number by pressing the numeric buttons. Note: When entering a single digit number (2 for example), either input "02" or just input "2" and wait for a few seconds. RECALLING A PRESET STATION 1. 1. SURROUND MODE PURE DIRECT SIMPLE SETUP AUTO HT-EQ MENU ENTER DISPLAY MEMORY CLEAR EXIT BAND T-MODE SLEEP DISPLAY P.DIRECT SURROUND AUTO 12 LIP SYNC/ dts INPUT 3 CS EX/ES VIRTUAL T.MODE 456 M-CH ST 7 STEREO 8 NIGHT 9 P.SCAN 7.1CH IN A/D HT-EQ CL 0 +10 MEMO CH/ CAT SPKR A/B MUTE VOLUME REC T.DISP PTY F.DIRECT 1. - PRESET + - TUNING + DISC+ ANGLE SUB TITLE AUDIO (Using the unit) 1. Select the desired preset station by pressing the 1 or 2 cursor buttons on the front panel (Using the remote controller) 1. Press the S or T buttons to select the desired preset station, or input your desired preset channel with the numeric buttons on the remote controller. PRESET SCAN 3. CS EX/ES VIRTUAL T.MODE 456 M-CH ST 7 STEREO 8 NIGHT 9 P.SCAN 7.1CH IN A/D HT-EQ CL 0 +10 MEMO CH/ CAT SPKR A/B MUTE VOLUME 1. 3. REC T.DISP PTY F.DIRECT - PRESET + - TUNING + DISC+ ANGLE SUB TITLE AUDIO CH-SEL V-OFF ATT. 3. (Using the remote controller) 1. Press the P.SCAN on the remote controller. "PRESET SCAN" appears on the display and then the preset station with the lowest preset number is recalled first. 2. Preset stations are recalled in sequence (No.1 → No.2 → etc.) for 5 seconds each. No stored preset number will be skipped. 3. You can fast forward the preset stations by pressing the T continuously. When the desired preset station is received, cancel the preset scan operation by pressing the CLEAR button or P.SCAN on the remote controller. CLEARING STORED PRESET STATIONS You can remove preset stations from the memory using the following procedure. 2. 3. VOLUME ENTER DISPLAY MEMORY CLEAR EXIT BAND T-MODE DOWN MUTE DIGITAL AUX 1 INPUT S-VIDEO VIDEO 2. 3. AUTO 12 LIP SYNC/ dts INPUT 3 CS EX/ES VIRTUAL T.MODE 456 M-CH ST 7 STEREO 8 NIGHT 9 P.SCAN 7.1CH IN A/D HT-EQ CL 0 +10 MEMO CH/ CAT SPKR A/B MUTE VOLUME MULTI/ CAT M-SPKR INFO MENU 1. Recall the preset number to be cleared with the method described in "Recalling" a preset station. 2. Press the MEMORY button on the front panel or press the MEMO button on the remote controller. 3. The stored preset number blinks in the display for 5 seconds. While blinking, press the CLEAR button on the front panel or the remote controller. 4. "xx CLEAR" appears on the display to indicate that the specified preset number has been cleared. Note: To clear all stored preset stations, press and hold the CLEAR and the ENTER buttons for two seconds. SORTING PRESET STATIONS AV SURROUND RECEIVER SR5002 INPUT SELECTOR VOLUME MULTI MULTI SPEAKER STANDBY POWER ON/STANDBY SETUP MIC PHONES SURROUND MODE PURE DIRECT SIMPLE SETUP AUTO HT-EQ MENU ENTER DISPLAY MEMORY CLEAR EXIT BAND T-MODE DOWN UP MUTE ATT DIGITAL AUX 1 INPUT S-VIDEO VIDEO L AUDIO R If you have stations memorized, and there is a gap in the sequential order: I.e. the stations are stored as follows 1) 87.1 MHz 2) 93.1 MHz 3) 94.7 MHz 10) 105.9 MHz (notice there is no stations programmed for pre sets for 4-9), you can have pre set 10 become pre set 5: To sort the numbers, press the 4 cursor button while pressing the MEMORY button. "PRESET SORT" will appear on the display and sorting will be done. NAME INPUT OF THE PRESET STATION. This function allows the name of each preset channel to be entered using alphanumeric characters. Before name inputting, you need to store preset stations with the preset memory operation. 4. 5. 2. 5. 6. AV SURROUND RECEIVER SR5002 INPUT SELECTOR VOLUME MULTI MULTI SPEAKER STANDBY POWER ON/STANDBY SETUP MIC PHONES SURROUND MODE PURE DIRECT SIMPLE SETUP AUTO HT-EQ MENU ENTER DISPLAY MEMORY CLEAR EXIT BAND T-MODE DOWN UP MUTE ATT DIGITAL AUX 1 INPUT S-VIDEO VIDEO L AUDIO R 2. 5. 6. 5. 4. 789 7.1CH IN A/D HT-EQ CL 0 +10 MEMO CH/ CAT SPKR A/B MUTE VOLUME MULTI/ CAT M-SPKR INFO MENU T.TONE /SET UP ENTER EXIT REC T.DISP PTY F.DIRECT - PRESET + - TUNING + DISC+ ANGLE SUB TITLE AUDIO CH-SEL V-OFF ATT. BASS TV DVD TREBLE VCR DSS 1. Recall the preset number to be inputted name with the method described in "Recalling" a preset station. 2. Press the MEMORY button on the front panel or press the MEMO button on the remote controller for more than 3 seconds. 3. The left most column of the station name indicator flashes, indicating the character entry ready status. 4. When you press the 3 or 4 cursor buttons on the front panel or the 5 / 6 buttons on the remote controller, alphabetic and numeric characters will be displayed in the following order: A → B → C ... Z → 1 → 2 → 3 ..... 0 Blank) → A UP → ← DOWN 5. After selecting the first character to be entered, press the MEMORY or ENTER buttons, press the MEMO button on the remote controller. The entry in this column is fixed and the next column starts to flash. Fill the next column the same way. To move back and forth between the characters, press the 1 / 2 cursor buttons or press S or T buttons on the remote controller. Note: Unused columns should be filled by entering blanks. 6. To save the name, press the MEMORY button on the front panel or remote controller for more than 2 seconds. Ten keypad 1 2 3 4 5 6 7 8 9 0 Press, press again, press again, etc. A → B → C → 1 → A D → E → F → 2 → D G → H → I → 3 → G J → K → L → 4 → J M → N → O → 5 → M P → Q → R → 6 → P S → T → U → 7 → S V → W → X → 8 → V Y → Z → space → 9 → Y 0 43