Marantz SR5002 SR4002_Rear_Panel_Drawing - Page 47

ENGLISH LISTENING TO XM SATELLITE RADIO (SR5002 ONLY) SELECTING AN INPUT SOURCE Before you can listen to XM Satellite Radio, you must first select the input source on the SR5002. 1. AV SURROUND RECEIVER SR5002 INPUT SELECTOR MULTI MULTI SPEAKER STANDBY POWER ON/STANDBY SETUP MIC PHONES SURROUND MODE PURE DIRECT AUTO HT-EQ SOURCE l/ SET SLEEP DISPLAY OFF ON P.DIRECT SURROUND AUTO 12 LIP SYNC/ dts INPUT 3 BAND CS EX/ES VIRTUAL T.MODE 456 M-CH ST 7 STEREO 8 NIGHT 9 P.SCAN 7.1CH IN A/D HT-EQ CL 0 +10 MEMO DISC+ ANGLE SUB TITLE AUDIO CH-SEL V-OFF ATT. BASS TV DVD TREBLE VCR DSS TUNER CD CDR MD TAPE AUX1 AUX2 AMP 2. 1. REMOTE CONTROLLER RC5001SR AV SURROUND RECEIVER SR5002 INPUT SELECTOR 2. VOLUME MULTI MULTI SPEAKER STANDBY POWER ON/STANDBY SETUP MIC PHONES SURROUND MODE PURE DIRECT SIMPLE SETUP AUTO HT-EQ MENU ENTER DISPLAY MEMORY CLEAR EXIT BAND T-MODE DOWN UP MUTE ATT DIGITAL AUX 1 INPUT S-VIDEO VIDEO L AUDIO R (Using the SR5002) 1. Turn the INPUT SELECTOR knob to select "TUNER". 2. Press the BAND button to select XM band. (Using the remote controller) 1. To select tuner, Press the TUNER button twice within two seconds on the remote controller. 2. Press the BAND button to select XM band. CHECKING THE XM SIGNAL STRENGTH AND RADIO ID T.TONE /SET UP ENTER EXIT REC T.DISP PTY F.DIRECT - PRESET + - TUNING + DISC+ ANGLE SUB TITLE AUDIO CH-SEL V-OFF ATT. BASS TREBLE 1. 1. Press the T.DISP button 3 times to displayed Signal Status. SIGNAL: • The display changes as shown below according to the receiving condition. SIGNAL SIGNAL: STRONG (Signal strength is good) SIGNAL SIGNAL: MARGINAL (Signal strength is Marginal) SIGNAL: ■■ SIGNAL: WEAK (Signal strength is poor) XM NO SIGNAL SIGNAL: NON (Loss of the signal) 2. Adjust the antenna location until signal strength is good. 3. Select channel 0 (XM000) with the 3 or 4 cursor buttons of the SR5002 or the Q or R buttons of the remote controller. AV SURROUND RECEIVER SR5002 INPUT SELECTOR 3. MULTI MULTI SPEAKER STANDBY POWER ON/STANDBY SETUP MIC PHONES SURROUND MODE PURE DIRECT SIMPLE SETUP AUTO HT-EQ MENU ENTER DISPLAY EXIT INFO MENU T.TONE /SET UP ENTER EXIT REC T.DISP PTY F.DIRECT - PRESET + - TUNING + DISC+ ANGLE SUB TITLE AUDIO CH-SEL V-OFF ATT. BASS TV DVD TREBLE VCR DSS TUNER CD CDR MD TAPE AUX1 AUX2 AMP 3. REMOTE CONTROLLER • The Radio ID is displayed. XMOOORADIO ID Notes: • If "ANTENNA" appears in the front panel display, the XM Mini-Tuner and Home Dock may not be connected to the XM terminal on the rear panel of this unit properly. • The ATT function is also effective when XM is selected. SWITCHING XM INFORMATION IN THE FRONT PANEL DISPLAY You can display XM information (such as artist name/ song title, category or signal status) for the channel currently selected in the front panel display. T.TONE /SET UP ENTER EXIT REC T.DISP PTY F.DIRECT - PRESET + - TUNING + 1. DISC+ ANGLE SUB TITLE AUDIO CH-SEL V-OFF ATT. BASS TREBLE 1. Press the T.DISP button to displayed */'03."5*0/ Channel number/name Artist name/Song title Channel category Signal Status When the Channel number/name is displayed: XMO40:DeepTrc 40:DeepTracks (If text is more than 13 characters long, the text is scrolled.) Note: The front Panel display can indicate up to 13 alphanumeric characters at once. If the information contains more then 13 characters, the information scrolls from right to left. 44