Marantz SR5002 SR4002_Rear_Panel_Drawing - Page 43

ENGLISH LISTENING THROUGH HEADPHONES This jack may be used to listen to the unit's output through a pair of headphones. Be certain that the headphones have a standard 1/4" stereo phono plug. Note that the speakers will automatically be turned off when the headphone jack is in use. AV SURROUND RECEIVER SR5002 INPUT SELECTOR MULTI MULTI SPEAKER STANDBY POWER ON/STANDBY SETUP MIC PHONES SURROUND MODE PURE DIRECT SIMPLE SETUP AUTO HT-EQ MENU Notes: • When using headphones, the surround mode will change to BYPASS and Dolby Headphone by MENU and Cursor button. • The surround mode returns to the previous setting as soon as the headphone plug is removed from the jack. • The tone control function can not work through the headphones output. DOLBY HEADPHONE MODE This feature simulates the waveforms of the actual sounds heard from the speakers. When headphones are used, the MENU button automatically switches to the Dolby headphone mode. The OSD that appears when the MENU button is pressed is shown below. HEAD PHONE DOLBY HP MODE : ON SURROUND : OFF L LEVEL R LEVEL : 0 dB : 0 dB DOLDBY HP (Headphone) MODE can be selected with the left and right cursor buttons. BYPASS → ON → BYPASS BYPASS: Bypasses the Dolby headphone mode and delivers ordinary 2-channel stereo. ON: Dolby headphone mode active. When the PURE DIRECT and SOURCE DIRECT mode is selected, Dolby surround processing is bypassed and is displayed as the mode indication. The surround mode can be selected when mode is ON. L/R LEVEL can be set in the ±10 dB range. Notes: • The surround mode returns to the previous setting as soon as the plug is removed from the jack. • The Dolby Headphone function will not work when 32 or 96 kHz PCM digital signals are input. ATTENUATION TO ANALOG INPUT SIGNAL REC T.DISP PTY F.DIRECT - PRESET + - TUNING + DISC+ ANGLE SUB TITLE AUDIO CH-SEL V-OFF ATT. BASS TV DVD TREBLE VCR DSS TUNER CD CDR MD If the selected analog audio input signal is greater than the capable level of internal processing, the "PEAK" indicator will light up on the front display. If this happens, you should press the ATT button on the remote controller. "ATT" indicator will be illuminated when this function is activated. The signal-input level is reduced by about half. Attenuation will not work with the output signal of TAPE-OUT, CD/CDR-OUT and VCR-OUT. This function is memorized for each individual input source. SPEAKER A/B M-CH ST 7 STEREO 8 NIGHT 9 P.SCAN 7.1CH IN A/D HT-EQ CL 0 +10 MEMO CH/ CAT SPKR A/B MUTE VOLUME MULTI/ CAT M-SPKR INFO MENU This unit has speaker system - A and speaker system- B for front L/R channels. You can select these systems by pressing SPEAKERS A/B button on the front panel or SPKAB on the remote controller. 7.1 CH INPUT This unit is equipped for future expansion through the use of Multi channel Super Audio CD multichannel player or DVD-Audio player. When this is selected, the input signals connected to the L(front left), R (front right), CENTER, SL (surround left), SR (surround right) and SBL (surround back left) and SBR (surround back right) channels of the 7.1 CH. In jacks are output directly to the front (left and right), center, surround (left and right) and surround back speaker systems as well as the pre-out jacks without passing through the surround circuitry. In addition, the signal input to the SW (subwoofer) jack is output to the PRE OUT SW (subwoofer) jack. When 7.1 CH. INPUT is selected, the last video input used remains routed to the Monitor Outputs. This permits simultaneous viewing with video sources. 40