Marantz SR5002 SR4002_Rear_Panel_Drawing - Page 25
Advanced Connecting, Connecting The Remote Control Jacks
View all Marantz SR5002 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 25 highlights
ENGLISH ADVANCED CONNECTING CONNECTING THE REMOTE CONTROL JACKS RL RL RL RL RL RL CENTER L R FRONT SURR. SURR. SUB BACK WOOFER DVD Audio player or Super Audio CD Multi channel player VIDEO FM (75) GND AM ANTENNA L SL C L S-VIDEO TV SBL DVD VCR IN R R SR SW (AUX2) 7.1CH INPUT SBR MULTI. OUT TV RS-232C SPEAKER C OFF ON DVD IN VCR L SL C SBL R L FRONT B R SR SW SBR FRONT A OR B.CENTER. FRONT A + B : 8 OHMS PRE OUT RL RL RL CENTER L R FRONT SURR. SURR. SUB BACK WOOFER Power Amplifer Subwoofer INPUT 1 COMPONENT INPUT 3 VIDEO MONITOR 1 OUT 2 DVD VCR IN VCR OUT DSS INPUT MONITOR OUT 2 Y CB/PB CR/PR Y CB/PB CR/PR Y CB/PB CR/PR INPUT 1 2 IN 4 5 DVD IN OUT VCR DSS IN OUT TAPE AUDIO 1 IN OUT CD/CDR 2 3 DIGITAL IN OPT OUT DIGITAL OUT REMOTE CONT. FLASHER DC IN TRIGGER L R L R L R L AC IN FRONT B FRONT A OR B.CENTER. FRONT A + B : 8 OHMS FRONT A SURROUND BACK SURROUND SPEAKER C/MULTI SPEAKER SURR.SURR BACK : 6-8 OHMS CENTER SPEAKER SYSTEMS SWITCHED 1.25A 150W AC OUTLETS 120V 60Hz 1 MODEL NO. SR5002 REMOTE CONTROL IN OUT CD recorder EXTERNAL INTERNAL REMOTE CONTROL IN OUT DVD player EXTERNAL INTERNAL RC OUT OPTION REMOTE CONTROL IN OUT CD player EXTERNAL INTERNAL LR LR LR CONNECTING MULTI CHANNEL AUDIO SOURCE The 7.1CH INPUT jacks are for multichannel audio source such as a Super Audio CD multichannel player, DVD audio player or external decoder. If you use these jacks, switch on the 7.1CH INPUT and set the 7.1CH INPUT level by using the SETUP MAIN MENU. See page 31. Front Left Center Front Right Surround Left Surround Right Surround Back Left Surround Back Right CONNECTING AN EXTERNAL POWER AMPLIFIER The PREOUT jacks are for connecting external power amplifiers. Be sure to connect each speaker to the corresponding external power amplifier. q You can control other Marantz products through this unit with the remote controller by connecting the REMOTE CONTROL terminals on each unit. The signal transmitted from the remote controller is received by the remote sensor on this unit. Then the signal is sent to the connected device through this terminal. Therefore you need to aim the remote signal only to the unit. Also, if a Marantz power amplifier (some models excluded) is connected to one of these terminals, the power amplifier's, power switch is synchronized with this unit's power switch. Set the REMOTE CONTROL SWITCH on the back of other units (not the SR4002/SR5002) to "EXT".(EXTERNAL) to use this feature. w Whenever external infrared sensors or similar devices are connected to RC-5 IN of the unit, be sure to always disable operation of the infrared sensor on the unit by using the following procedure. 1. Hold down the 7.1CH INPUT (SR4002) / MULTI (SR5002) button and MENU button on the front panel at the same time for five seconds. 2. The setting "IR=ENABLE" is shown on the FL DISPLAY. 3. Press the 1 or 2 cursor button to change this to "IR=DISABLE". 4. Press the ENTER button. Once this setting is made, the infrared sensor on the unit is disabled. Note: Be sure to set to "IR=ENABLE" when external infrared sensors or similar devices are not connected. Otherwise, the unit will be unable to receive remote control commands. 5. To restore the original setting, perform steps 1 to 4 to set to "IR=ENABLE". 22