Marantz SR5002 SR4002_Rear_Panel_Drawing - Page 37

ENGLISH BASIC OPERATION (PLAYBACK) SELECTING AN INPUT SOURCE Before you can listen to any input media, you must first select the input source on the unit. Example : DVD AV SURROUND RECEIVER SR5002 INPUT SELECTOR MULTI MULTI SPEAKER STANDBY POWER ON/STANDBY SETUP MIC PHONES SURROUND MODE PURE DIRECT SIMPLE SETUP AUTO HT-EQ MENU DISC+ ANGLE SUB TITLE AUDIO CH-SEL V-OFF ATT. BASS TV DVD TREBLE VCR DSS TUNER CD CDR MD TAPE AUX1 AUX2 AMP SELECTING THE SURROUND MODE Example: AUTO SURROUND AV SURROUND RECEIVER SR5002 INPUT SELECTOR MULTI MULTI SPEAKER STANDBY POWER ON/STANDBY SETUP MIC PHONES SURROUND MODE PURE DIRECT SIMPLE SETUP AUTO HT-EQ MENU SOURCE l/ SET SLEEP DISPLAY OFF ON P.DIRECT SURROUND AUTO 12 LIP SYNC/ dts INPUT 3 CS EX/ES VIRTUAL T.MODE 456 M-CH ST 7 STEREO 8 NIGHT 9 P.SCAN 7.1CH IN A/D HT-EQ CL 0 +10 MEMO To select the surround mode during playback, press the SURROUND MODE button on the front panel or the SURROUND MODE buttons on the remote controller. REMOTE CONTROLLER To select DVD, turn the INPUT SOURCE knob on the front panel or simply press the DVD button on the remote controller. After you have selected DVD, simply turn on the DVD player and play the DVD. • As the input source is changed, the new input name will appear momentarily an OSD information on the video display. The input name will also appear in the display, on the front-panel. • As the input is changed, this unit will automatically switch to the digital input, surround mode, attenuation, and night mode status which were entered during the configuration process for that source. • When an audio source is selected, the last video input used remains routed to the VCR Output and Monitor Output. This permits simultaneous viewing and listening to different sources. • When a Video source is selected, the video signal for that input will be routed to the Monitor Output jacks and will be viewable on a TV monitor connected to the unit. If a component video input is connected to the DVD or DSS component inputs, it will be routed to the Component Video Output. Make certain that your TV is set to the proper input to view the signal. NIGHT MODE AUTO 12 LIP SYNC/ dts INPUT 3 CS EX/ES VIRTUAL T.MODE 456 M-CH ST 7 STEREO 8 NIGHT 9 P.SCAN 7.1CH IN A/D HT-EQ CL 0 +10 MEMO CH/ CAT SPKR A/B MUTE VOLUME Press the NIGHT button on the remote controller to turn on the NIGHT mode. Selecting the Night Mode ON is effective in Dolby Digital only, and it compresses the dynamic range. This softens loud passages such as sudden explosions, to help prevent disturbing others late at night. To turn off the Night mode, press the NIGHT button again. 34 ADJUSTING THE MAIN VOLUME VOLUME SPLAY MEMORY CLEAR EXIT BAND T-MODE DOWN UP MUTE ATT DIGITAL AUX 1 INPUT S-VIDEO VIDEO L AUDIO R 7.1CH IN A/D HT-EQ CL 0 +10 MEMO CH/ CAT SPKR A/B MUTE VOLUME MULTI/ CAT M-SPKR INFO MENU ENTER TEMPORARILY TURNING OFF THE SOUND VOLUME ISPLAY MEMORY CLEAR EXIT BAND T-MODE DOWN UP MUTE ATT DIGITAL AUX 1 INPUT S-VIDEO VIDEO L AUDIO R 7.1CH IN A/D HT-EQ CL 0 +10 MEMO CH/ CAT SPKR A/B MUTE VOLUME MULTI/ CAT M-SPKR INFO MENU ENTER Adjust the volume to a comfortable level using the VOLUME control knob on the front panel or To temporarily silence all speaker outputs such as VOLUME 3 / 4 buttons on the remote controller. when interrupted by a phone call, press the MUTE To increase the volume, turn the VOLUME knob button on the front panel or MUTE button on the clockwise or press VOLUME 3 button on the remote controller. remote controller, to decrease the volume, turn This will interrupt the output to all speakers and the counterclockwise or press VOLUME 4 button on the head-phone jack, but it will not affect any recording or remote controller. dubbing that may be in progress. Notes: When the system is muted, the display will show • The volume can be adjusted within the range of - ∞ "MUTE" . to 18 dB, in steps of 1 dB. Press the MUTE button again to return to normal • However, when the channel level is set as described operation. on page 26, if the volume for any channel is set at +1 dB or greater, the volume cannot be adjusted up to 18 dB. USING THE SLEEP TIMER (In this case the maximum volume adjustment range is "18 dB - Maximum value of channel level) ADJUSTING THE TONE (BASS & TREBLE) CONTROL - PRESET + - TUNING + DISC+ ANGLE SUB TITLE AUDIO CH-SEL V-OFF ATT. BASS TV DVD TREBLE VCR DSS TUNER CD CDR MD TAPE AUX1 AUX2 AMP REMOTE CONTROLLER LEARN SEND SOURCE l/ SET SLEEP DISPLAY OFF ON P.DIRECT SURROUND AUTO 1 CS 4 2 EX/ES 5 LIP SYNC/ dts INPUT 3 VIRTUAL T.MODE 6 To program this unit for automatic standby, press the SLEEP button on the remote controller. Each press of the button will increase the time before shut down in the following sequence. OFF 10 20 30 40 50 120 110 100 90 80 70 60 During a listening session you may wish to adjust the Bass and Treble Control to suit your listening tastes The sleep time will be shown for a few seconds in the or room acoustics. display on the front panel, and it will count down until the time has elapsed. (Using the remote controller) When the programmed sleep time has elapsed, the To adjust the bass effect, press BASS 3 or BASS 4 unit will automatically turn off. on the remote controller. To adjust the treble effect, press TREBLE 3 or Note that the SLEEP indicator on the display will illuminate when the Sleep function is programmed. TREBLE 4 on the remote controller. To cancel the Sleep function, press the SLEEP Note: button until the display shows "SLEEP OFF" and the The tone control function can work in the AUTO SLEEP indicator will disappear. Surround, Stereo, Dolby PLIIx, DTS, DTS-ES, and Multi Ch. Stereo mode.