NEC UN552S User Manual English - Page 21

Installing an Optional Sensor Unit

Get NEC UN552S PDF manuals and user guides View all NEC UN552S manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

English Installing an Optional Sensor Unit For installing the sensor to the monitor, please use the screw or the double-sided tape as shown below: Seal 8 mm Double-sided tape Screw Position Fixed by screw: Remove the seal covering screw holes on the bezel. Secure the unit with the attached screw. Set the sensor unit close to the back side.  NOTE: Depending on the type of the monitor, there are limitations for mounting. For installation, follow instructions below to avoid damage to the monitor. For the UN462A/UN462VA/UN552A: • When installing the sensor unit on the upper side of the monitor, do not use the screw. If the sensor unit is installed using a screw, it could damage the monitor. For the UN492S/UN492VS: • Please use the M3 x 6 screw attached to the monitor. It isn't possible to use a screw of the Optional Sensor Unit. For fixing the sensor unit within the bezel, it is recommended using screw holes as below mentioned. Fixed by double-sided tape: You can set the sensor unit on any side of the monitor. Set the sensor unit 8 mm away from the front edge.  NOTE: For the UN552S/UN552VS: • Please use double-sided tape only.  English−17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
English
English−17
Installing an Optional Sensor Unit
For installing the sensor to the monitor, please use the screw or the double-sided tape as shown below:
Seal
Screw Position
Double-sided tape
8 mm
Fixed by screw°
Remove the seal covering screw holes on the bezel. Secure the unit with the attached screw.
Set the sensor unit close to the back side.
NOTE°
Depending on the type of the monitor, there are limitations for mounting. For installation, follow instructions below to
avoid damage to the monitor.
For the UN462A/UN462VA/UN552A°
•
When installing the sensor unit on the upper side of the monitor, do not use the screw. If the sensor unit is installed
using a screw, it could damage the monitor.
For the UN492S/UN492VS°
•
Please use the M3 x 6 screw attached to the monitor. It isn’t possible to use a screw of the Optional Sensor Unit.
For fixing the sensor unit within the bezel, it is recommended using screw holes as below mentioned.
Fixed by double-sided tape°
You can set the sensor unit on any side of the monitor.
Set the sensor unit 8 mm away from the front edge.
NOTE°
For the UN552S/UN552VS°
•
Please use double-sided tape only.