NEC UN552S User Manual English - Page 37

Power ON and OFF Modes

Get NEC UN552S PDF manuals and user guides View all NEC UN552S manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

English Power ON and OFF Modes Press the button on the Control Panel or POWER ON button on the Remote Control to turn on the monitor. The monitor's power LED indicates the current status of the monitor. Please refer to the following table for information about the LED indicator. LED indicator status and lighting pattern Condition Recovery Glowing blue Blinking green*1 Normal Under any of the conditions below, no input signal has been detected by the monitor during the period of time you set: 1. Turn on the monitor by the remote control or the monitor button. 2. Send an AV signal input to the monitor. • The monitor is using an Option Board. • [INPUT DETECT] is set to a setting except for [NONE]. • [USB POWER] is set to [ON]. • DisplayPort in the [TERMINAL SETTINGS] is set to [MST]. Glowing amber No AV signal input has been detected by the monitor during the period of time you set. (with network signal input) Blinking amber No AV signal input has been detected by the monitor during the period of time you set. (no network signal input) Glowing red Turn off the monitor by the remote control or the monitor button. Turn on the monitor by the remote control or the monitor button. *1: Time setting for [AUTO POWER SAVE] is available at [POWER SAVE] (See page 122).  NOTE: • The blue LED indicator that the monitor is powered on and functioning normally can be turned off in the monitor's OSD menu options. See page 126. • If the indicator is blinking red in a combination of long and short durations, a certain failure might have occurred, please contact your supplier. The Main Power switch must be in the ON position in order to power up the monitor using the POWER ON button on the remote control or the button on the Control Panel. OFF ON Main Power Switch Button English−33

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
English
English−33
Power ON and OFF Modes
Press the
button on the Control Panel or POWER ON button on the Remote Control to turn on the monitor.
The monitor’s power LED indicates the current status of the monitor. Please refer to the following table for information about the
LED indicator.
LED indicator status and
lighting pattern
Condition
Recovery
Glowing blue
Normal
1.
Turn on the monitor by the remote
control or the monitor button.
2.
Send an AV signal input to the
monitor.
Blinking green*
1
Under any of the conditions below, no input signal has
been detected by the monitor during the period of time you
set:
•
The monitor is using an Option Board.
•
[INPUT DETECT] is set to a setting except for [NONE].
•
[USB POWER] is set to [ON].
•
DisplayPort in the [TERMINAL SETTINGS] is set to
[MST].
Glowing amber
No AV signal input has been detected by the monitor during
the period of time you set. (with network signal input)
Blinking amber
No AV signal input has been detected by the monitor during
the period of time you set. (no network signal input)
Glowing red
Turn off the monitor by the remote control or the monitor
button.
Turn on the monitor by the remote
control or the monitor button.
*
1
:
Time setting for [AUTO POWER SAVE] is available at [POWER SAVE] (See
page 122
).
NOTE°
•
The blue LED indicator that the monitor is powered on and functioning normally can be turned off in the monitor’s
OSD menu options. See
page 126
.
•
If the indicator is blinking red in a combination of long and short durations, a certain failure might have occurred,
please contact your supplier.
The Main Power switch must be in the ON position in order to power up the monitor using the POWER ON button on the remote
control or the
button on the Control Panel.
Main Power Switch
OFF
ON
Button