Netgear WAG302v2 WAG302v2 Reference Manual - Page 22

Rear Panel, RJ-45 Ethernet LAN/POE Port. Use the WAG302v2 Ethernet RJ-45 port to connect to an - reset

Get Netgear WAG302v2 - ProSafe Dual Band Wireless Access Point PDF manuals and user guides View all Netgear WAG302v2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

NETGEAR ProSafe Dual Band Wireless Access Point WAG302v2 Reference Manual LED Description 802.11a WLAN Wireless LAN Link Activity Indicator (5 GHz) Off No wireless link activity. Green Blink Wireless link activity. 802.11g WLAN Wireless LAN Link Activity Indicator (2.4 MHz) Off No wireless link activity. Green Blink Wireless link activity. Rear Panel 1 3 2 4 5 6 Figure 1-2 The numbers in Figure 1-2 correspond to the following features on the back of the WAG302v2: 1. 5 GHz detachable antenna. The 5 GHz antenna supports clients that use the 802.11a radio. The WAG302v2 will not function properly if the 5 GHz antenna is not attached to the correct port. The antenna frequency is labeled near its base. 2. 2.4 GHz detachable antenna. The 2.4 GHz antenna supports clients that use the 802.11b/g radio. The WAG302v2 will not function properly if the 2.4 GHz antenna is not attached to the correct port. The antenna frequency is labeled near its base. 3. Reset button. This restores the default factory settings. 4. Serial Console Port. Use the male DB-9 serial port for serial DTE connections. 5. RJ-45 Ethernet LAN/POE Port. Use the WAG302v2 Ethernet RJ-45 port to connect to an Ethernet LAN through a device such as a hub, switch, router, or Power Over Ethernet (POE) switch. 6. Power socket. This connects to the WAG302v2 power adapter. 1-6 Introduction v1.0, May 2006

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
NETGEAR ProSafe Dual Band Wireless Access Point WAG302v2 Reference Manual
1-6
Introduction
v1.0, May 2006
Rear Panel
The numbers in
Figure 1-2
correspond to the following features on the back of the WAG302v2:
1.
5 GHz detachable antenna. The 5 GHz antenna supports clients that use the 802.11a radio. The
WAG302v2 will not function properly if the 5 GHz antenna is not attached to the correct port.
The antenna frequency is labeled near its base.
2.
2.4 GHz detachable antenna. The 2.4 GHz antenna supports clients that use the 802.11b/g
radio. The WAG302v2 will not function properly if the 2.4 GHz antenna is not attached to the
correct port. The antenna frequency is labeled near its base.
3.
Reset button. This restores the default factory settings.
4.
Serial Console Port. Use the male DB-9 serial port for serial DTE connections.
5.
RJ-45 Ethernet LAN/POE Port. Use the WAG302v2 Ethernet RJ-45 port to connect to an
Ethernet LAN through a device such as a hub, switch, router, or Power Over Ethernet (POE)
switch.
6.
Power socket. This connects to the WAG302v2 power adapter.
802.11a WLAN
Wireless LAN Link Activity Indicator (5 GHz)
Off
No wireless link activity.
Green Blink
Wireless link activity.
802.11g WLAN
Wireless LAN Link Activity Indicator (2.4 MHz)
Off
No wireless link activity.
Green Blink
Wireless link activity.
Figure 1-2
LED
Description
2
1
3
4
5
6