Netgear WAG302v2 WAG302v2 Reference Manual - Page 29

Logging in to the WAG302v2 Using Its Default IP Address, Open a Web browser such as Internet Explorer - login

Get Netgear WAG302v2 - ProSafe Dual Band Wireless Access Point PDF manuals and user guides View all Netgear WAG302v2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

NETGEAR ProSafe Dual Band Wireless Access Point WAG302v2 Reference Manual Logging in to the WAG302v2 Using Its Default IP Address After you install the WAG302v2, log in to it to configure the basic settings and the wireless settings. The WAG302v2 is set, by default, with the IP address of 192.168.0.230 with DHCP disabled. You can log in to the WAG302v2 by using the HTTP or HTTPS protocol. Note: Unless you change the IP address or enable the DHCP client on the WAG302v2, the computer that you use to connect to the WAG302v2 should be configured with an IP address that starts with 192.168.0.x and a Subnet Mask of 255.255.255.0. 1. Open a Web browser such as Internet Explorer, Netscape Navigator, or Mozilla Firefox. 2. Connect to the WAG302v2 by entering its default address of http://192.168.0.230 into your browser. Figure 2-3 Note: To use the HTTPS protocol, enter https://192.168.0.230 into your browser and accept the certificate. 3. A login window like the one shown below opens: Figure 2-4 Basic Installation and Configuration 2-7 v1.0, May 2006

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
NETGEAR ProSafe Dual Band Wireless Access Point WAG302v2 Reference Manual
Basic Installation and Configuration
2-7
v1.0, May 2006
Logging in to the WAG302v2 Using Its Default IP Address
After you install the WAG302v2, log in to it to configure the basic settings and the wireless
settings. The WAG302v2 is set, by default, with the IP address of 192.168.0.230 with DHCP
disabled. You can log in to the WAG302v2 by using the HTTP or HTTPS protocol.
1.
Open a Web browser such as Internet Explorer, Netscape Navigator, or Mozilla Firefox.
2.
Connect to the WAG302v2 by entering its default address of
into your
browser.
3.
A login window like the one shown below opens:
Note:
Unless you change the IP address or enable the DHCP client on the WAG302v2,
the computer that you use to connect to the WAG302v2 should be configured with
an IP address that starts with 192.168.0.x and a Subnet Mask of 255.255.255.0.
Figure 2-3
Note:
To use the HTTPS protocol, enter
into your browser and
accept the certificate.
Figure 2-4