Home » Netgear Manuals » Wireless » Netgear WAG302v2 » Manual Viewer

Netgear WAG302v2 WAG302v2 Reference Manual - Page 99

Viewing and Configuring System Information, Available Wireless Station List

Add to My Manuals
Save this manual to your list of manuals

Page 99 highlights

NETGEAR ProSafe Dual Band Wireless Access Point WAG302v2 Reference Manual Table C-12 AP Management Task Revert to factory default settings Reboot the system Command factory-reset reboot Viewing and Configuring System Information The commands in Table C-12 correspond to the pages on the Web UI under the Information heading. This section includes commands for the following features: • Activity Log • Available Wireless Station List • Statistics • Rogue AP Detection Table C-13 AP Information Task Command View the SysLog activity log get log-entry View all SysLog server information get log detail Enable SysLog set log relay-enabled 1 Disable SysLog set log relay-enabled 0 Set the IP address of the SysLog server set log relay-host Set the port number configured in the SysLog server View a list of wireless stations set log relay-port get association detail View interface statistics get interface all ip mac ssid txpackets tx-bytes tx-errors rx-packets rx-bytes rx-errors Turn Rogue AP Detection On set radio wlan0 ap-detection on Turn Rogue AP Detection Off set radio wlan0 ap-detection off View a list of unknown APs get unknown-ap View a list of known APs get known-ap-config Command Line Reference v1.0, May 2006 C-15

Section	Page
NETGEAR ProSafe Dual Band Wireless Access Point WAG302v2 Reference Manual	1
Contents	9
About This Manual	13
Conventions, Formats and Scope	13
How to Use This Manual	14
How to Print this Manual	15
Chapter 1 Introduction	17
Key Features	17
Supported Standards and Conventions	17
WAG302v2 Key Features	18
Compatible and Related NETGEAR Products	19
What’s In the Box?	20
Hardware Description	21
Front Panel	21
Rear Panel	22
Chapter 2 Basic Installation and Configuration	23
System Requirements	23
Wireless Equipment Placement and Range Guidelines	24
Installing the WAG302v2 Wireless Access Point	25
Logging in to the WAG302v2 Using Its Default IP Address	29
Basic IP Settings	30
Wireless Settings	32
Understanding WAG302v2 Wireless Security Options	35
Configuring Security Profiles	35
Profile Definition	38
Network Authentication	38
Data Encryption	39
Wireless Client Security Separation	40
VLAN ID	40
SSID and Wireless Security Settings Form	41
Configuring the RADIUS Server Settings	42
Restricting Wireless Access by MAC Address	43
Chapter 3 Management and Information	47
Changing the Administrator Password	47
Remote Management	48
Using the Secure Telnet Interface	49
Accessing the CLI by Using the Console Port	49
CLI Commands	50
Upgrading the Wireless Access Point Firmware	50
Configuration File Management	51
Backing up and Restoring the Configuration	52
Erasing the Configuration	52
Using the Reset Button to Restore Factory Default Settings	52
Viewing General Information	53
Viewing the Activity Log	55
Viewing the Available Wireless Station List	56
Viewing Statistics	57
Rogue AP Detection	58
Chapter 4 Advanced Configuration	61
Configuring Advanced IP Settings for Wireless Clients	61
Configuring Hotspot Settings	63
Configuring Advanced Wireless Settings	63
Configuring Wireless LAN Parameters	64
Modifying QoS Queue Parameters	65
Wireless Bridging and Repeating	67
Point-to-Point Bridge Configuration	69
Multi-Point Bridge Configuration	70
Repeater with Wireless Client Association	72
Chapter 5 Troubleshooting	75
No lights are lit on the access point.	75
The Wireless LAN activity light does not light up.	76
The LAN light is not lit.	76
I cannot access the Internet or the LAN with a wireless capable computer.	76
I cannot connect to the WAG302v2 to configure it.	77
When I enter a URL or IP address I get a timeout error.	77
I am unable to download files from some FTP sites.	78
I need to restore factory default settings.	78
Appendix A Related Documents	79
Appendix B Specifications	81
Default Factory Settings	81
Specifications for the WAG302v2	84
Appendix C Command Line Reference	85
Accessing CLI TAB Completion Help	85
Keyboard Shortcuts	86
Interface Naming Conventions	87
Entering CLI Commands	88
Using the CLI to Configure the WAG302v2 Wireless Access Point	89
Viewing General Information	90
Configuring Basic Settings	91
Configuring Wireless Settings	92
Configuring Security Profile Settings	93
RADIUS Server Settings	96
Access Control	97
Viewing and Configuring Management Settings	98
Viewing and Configuring System Information	99
Configuring Advanced IP Settings	100
Hotspot Settings	101
Advanced Wireless Settings	101