Netgear WAG302v2 WAG302v2 Reference Manual - Page 89

Using the CLI to Con the WAG302v2 Wireless Access Point

Get Netgear WAG302v2 - ProSafe Dual Band Wireless Access Point PDF manuals and user guides View all Netgear WAG302v2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 89 highlights

NETGEAR ProSafe Dual Band Wireless Access Point WAG302v2 Reference Manual Table C-3 Commands at the Blank Prompt (continued) Command config firmware-upgrade save-running reboot factory-reset Description Uploads or downloads the running configuration. Upgrades the firmware. Saves the running configuration as the startup configuration. Restarts the access point (a "soft" reboot). Resets the AP to factory defaults and reboots. Warning: Settings updated from the CLI (with get, set, add, and remove commands) will not be saved to the startup configuration unless you explicitly save them by issuing the save-running command. The get, set, add, and remove commands are followed by one or more keywords and might be followed by one or more optional or required name-value pairs. You can use CLI commands to view or configure most of the features that you can view and configure by using the Web UI. Note: CLI commands are not available to merge, import, and export the known AP list for Rogue AP detection feature. Additionally, you cannot set the channel or frequency by using the CLI. Using the CLI to Configure the WAG302v2 Wireless Access Point This section describes the commands you use to view and configure the WAG302v2. The CLI commands correspond to tasks you can accomplish by using the Web-based user interface (UI). In some cases, the CLI get command provides additional details not available through the Web UI. Command Line Reference C-5 v1.0, May 2006

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
NETGEAR ProSafe Dual Band Wireless Access Point WAG302v2 Reference Manual
Command Line Reference
C-5
v1.0, May 2006
The
get
,
set
,
add
, and
remove
commands are followed by one or more keywords and might
be followed by one or more optional or required name-value pairs.
You can use CLI commands to view or configure most of the features that you can view and
configure by using the Web UI.
Using the CLI to Configure the WAG302v2 Wireless Access
Point
This section describes the commands you use to view and configure the WAG302v2. The CLI
commands correspond to tasks you can accomplish by using the Web-based user interface (UI). In
some cases, the CLI
get
command provides additional details not available through the Web UI.
config
Uploads or downloads the running configuration.
firmware-upgrade
Upgrades the firmware.
save-running
Saves the running configuration as the startup configuration.
reboot
Restarts the access point (a “soft” reboot).
factory-reset
Resets the AP to factory defaults and reboots.
Warning:
Settings updated from the CLI (with
get
,
set
,
add
, and
remove
commands) will not be saved to the startup configuration unless you
explicitly save them by issuing the
save-running
command.
Note:
CLI commands are not available to merge, import, and export the known AP list
for Rogue AP detection feature. Additionally, you cannot set the channel or
frequency by using the CLI.
Table C-3
Commands at the Blank Prompt (continued)
Command
Description