Netgear WAG302v2 WAG302v2 Reference Manual - Page 49

Using the Secure Telnet Interface, Accessing the CLI by Using the Console Port, should appear.

Get Netgear WAG302v2 - ProSafe Dual Band Wireless Access Point PDF manuals and user guides View all Netgear WAG302v2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 49 highlights

NETGEAR ProSafe Dual Band Wireless Access Point WAG302v2 Reference Manual Using the Secure Telnet Interface The WAG302v2 includes a secure Telnet command line interface (CLI). You can access the CLI from a secure Telnet client over the Ethernet port or over the serial console port. Note: You must use a secure Telnet client such as PuTTY. Also, when you configure the client, use the SSH1, 3DES option. If you use the Telnet client to connect over the Ethernet port, use the IP address of the WAG302v2 as the host name. Accessing the CLI by Using the Console Port 1. Using a null-modem cable, connect a VT100/ANSI terminal or a workstation to the port labeled Console. If you attached a PC, Apple Macintosh, or UNIX workstation, start a secure terminalemulation program. 2. Configure the terminal-emulation program to use the following settings: • Baud rate: 9600 bps • Data bits: 8 • Parity: none • Stop bit: 1 • Flow control: none These settings appear below the connector on the back panel. 3. Press Enter, and a screen similar to the one in Figure 3-3 should appear. Figure 3-3 4. The the login name and password. The login name is admin and password is the default password. Management and Information 3-3 v1.0, May 2006

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
NETGEAR ProSafe Dual Band Wireless Access Point WAG302v2 Reference Manual
Management and Information
3-3
v1.0, May 2006
Using the Secure Telnet Interface
The WAG302v2 includes a secure Telnet command line interface (CLI). You can access the CLI
from a secure Telnet client over the Ethernet port or over the serial console port.
Accessing the CLI by Using the Console Port
1.
Using a null-modem cable, connect a VT100/ANSI terminal or a workstation to the port
labeled Console.
If you attached a PC, Apple Macintosh, or UNIX workstation, start a secure terminal-
emulation program.
2.
Configure the terminal-emulation program to use the following settings:
•
Baud rate: 9600 bps
•
Data bits: 8
•
Parity: none
•
Stop bit: 1
•
Flow control: none
These settings appear below the connector on the back panel.
3.
Press Enter, and a screen similar to the one in
Figure 3-3
should appear.
4.
The the login name and password. The login name is
admin
and
password
is the default
password.
Note:
You must use a secure Telnet client such as PuTTY. Also, when you configure the
client, use the SSH1, 3DES option. If you use the Telnet client to connect over the
Ethernet port, use the IP address of the WAG302v2 as the host name.
Figure 3-3