Home » Netgear Manuals » Wireless » Netgear WNDAP350 » Manual Viewer

Netgear WNDAP350 WNDAP350 User Manual - Page 110

Table A-1. Access Point Default Configuration Settings, Default Settings and Technical Specifications

UPC - 606449064643

Add to My Manuals
Save this manual to your list of manuals

Page 110 highlights

ProSafe Dual Band Wireless-N Access Point WNDAP350 Reference Manual Table A-1. Access Point Default Configuration Settings Feature Description DHCP Client Time Zone Time Zone Adjusted for Daylight Saving Time SNMP Spanning Tree Protocol Secure Telnet Wireless Disabled USA-Pacific Disabled Enabled, but Trap forwarding disabled Disabled Enabled Operating Mode Access Point Name Wireless Communication 11a/na Wireless Network Name (SSID) 11 b/bg/ng Wireless Network Name (SSID) Broadcast Network Name SSID Security Transmission Speed Country/Region 80211.a Radio Frequency Channel 80211.g Radio Frequency Channel Output Power Access Point netgearxxxxxx where xxxxxx are the last 6 digits of the wireless access point MAC address. Enabled NETGEAR_11a NETGEAR_11g Enabled Disabled Besta Varies by region Auto Auto Full Wireless Card Access List All wireless stations allowed WMM Support Enabled a. Maximum Wireless signal rate derived from IEEE Standard 802.11 specifications. Actual throughput will vary. Network conditions and environmental factors, including volume of network traffic, building materials and construction, and network overhead, lower actual data throughput rate. A-2 Default Settings and Technical Specifications v1.1, November 2009

Section	Page
ProSafe Dual Band Wireless-N Access Point WNDAP350 Reference Manual	1
Contents	7
About This Manual	11
Conventions, Formats, and Scope	11
How to Print This Manual	12
Revision History	12
Chapter 1 Introduction	13
About the ProSafe Dual Band Wireless-N Access Point WNDAP350	13
Key Features and Standards	13
Supported Standards and Conventions	14
Key Features	14
802.11a/b/g/n Standards-based Wireless Networking	16
Autosensing Ethernet Connections with Auto Uplink	16
Compatible and Related NETGEAR Products	17
System Requirements	17
What’s In the Box?	18
Hardware Description	18
Front Panel	19
Rear Panel	20
Chapter 2 Basic Installation and Configuration	21
Wireless Equipment Placement and Range Guidelines	22
Understanding WNDAP350 Wireless Security Options	23
Installing the WNDAP350 wirelss access point	24
Setting up the WNDAP350 wirelss access point	24
Configuring LAN and Wireless Access	25
Configuring Time Settings	28
Configuring Wireless Access	30
Deploying the WNDAP350 wirelss access point	30
Verifying Wireless Connectivity	31
Logging In Using the Default IP Address	32
Setting Basic IP Options	33
Wireless Settings	34
Configuring 802.11b/bg/ng Wireless Settings	34
Configuring 802.11a/na Wireless Settings	37
Configuring Basic QoS Settings	41
Setting Up and Testing Basic Wireless Connectivity	42
Understanding Security Profiles	43
SSID and WEP/WPA Settings Setup Form	47
802.11b/bg/ng Configuration	47
802.11a/na Configuration	48
Configuring the RADIUS Server Settings	49
Setting up a Security Profile	51
Configuring WEP	53
Configuring WPA with RADIUS	55
Configuring WPA2 with RADIUS	57
Configuring WPA and WPA2 with RADIUS	58
Configuring WPA-PSK	60
Configuring WPA2-PSK	61
Configuring WPA-PSK and WPA2-PSK	62
Restricting Wireless Access by MAC Address	64
Chapter 3 Management	67
Remote Management	67
Remote Console	69
Using the Secure Telnet Interface	69
CLI Commands	70
Upgrading the Wireless Access Point Software	71
Configuration File Management	72
Saving Your Configuration Settings	73
Restoring Saved Settings	73
Restoring the WNDAP350 to the Factory Default Settings	74
Changing the Administrator Password	76
Enabling the SysLog Server	77
Using Activity Log Information	78
Viewing General Summary Information	78
Viewing Network Traffic Statistics	80
Viewing Available Wireless Station Statistics	82
Enabling Rogue AP Detection	83
Importing Rogue AP List from a File	84
Viewing Rogue AP Statistics	85
Packet Capture	87
Chapter 4 Advanced Configuration	89
IP Settings for Wireless Clients	89
Hotspot Settings	91
Configuring Advanced Wireless Settings	92
Configuring 802.11b/bg/ng Advanced Wireless Settings	92
Configuring 802.11a/na Advanced Wireless Settings	94
Configuring Advanced QoS Settings	96
Enabling Wireless Bridging	98
Configuring a WNDAP350 as a Point-to-Point Bridge	101
Configuring a Point-to-Multi-Point Wireless Bridge	102
Chapter 5 Troubleshooting and Debugging	105
No lights are lit on the wireless access point.	105
The Wireless LAN activity light does not light up.	106
The LAN light is not lit.	106
I cannot access the Internet or the LAN with a wireless capable computer.	106
I cannot connect to the WNDAP350 to configure it.	107
When I enter a URL or IP address I get a timeout error.	107
Using the Reset Button to Restore Factory Default Settings	108
Appendix A Default Settings and Technical Specifications	109
Factory Default Settings	109
Technical Specifications	111
Appendix B Related Documents	113
Appendix C Command Line Reference	115
Command Sets	115