Netgear WNDAP350 WNDAP350 User Manual - Page 70

CLI Commands, Enter, admin, password - admin login

Get Netgear WNDAP350 - ProSafe 802.11n Dual Band Wireless Access Point PDF manuals and user guides
UPC - 606449064643
View all Netgear WNDAP350 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 70 highlights

ProSafe Dual Band Wireless-N Access Point WNDAP350 Reference Manual To use the CLI from a Console Port: 1. Using the null-modem cable, connect a VT100/ANSI terminal or a workstation to the port labeled Console. If you attached a PC, Apple Macintosh, or UNIX workstation, start a secure terminalemulation program. 2. Configure the terminal-emulation program to use the following settings: • Baud rate: 9600 bps • Data bits: 8 • Parity: none • Stop bit: 1 • Flow control: none These settings appear below the connector on the back panel. 3. Press Enter. The screen shown below in Figure 3-3 should appear. Figure 3-3 4. Enter the login name and password (admin and password are the defaults). After successful login, the prompt should appear. In this example, the prompt is netgear74F35E. 5. Enter help to display the CLI command help. CLI Commands The CLI commands are listed in Appendix C, "Command Line Reference." 3-4 Management v1.1, November 2009

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
ProSafe Dual Band Wireless-N Access Point WNDAP350 Reference Manual
3-4
Management
v1.1, November 2009
To use the CLI from a Console Port:
1.
Using the null-modem cable, connect a VT100/ANSI terminal or a workstation to the port
labeled Console.
If you attached a PC, Apple Macintosh, or UNIX workstation, start a secure terminal-
emulation program.
2.
Configure the terminal-emulation program to use the following settings:
•
Baud rate: 9600 bps
•
Data bits: 8
•
Parity: none
•
Stop bit: 1
•
Flow control: none
These settings appear below the connector on the back panel.
3.
Press
Enter
. The screen shown below in
Figure 3-3
should appear.
4.
Enter the login name and password (
admin
and
password
are the defaults).
After successful login, the <
Access Point Name
> prompt should appear. In this example, the
prompt is
netgear74F35E
.
5.
Enter
help
to display the CLI command help.
CLI Commands
The CLI commands are listed in
Appendix C, “Command Line Reference
.”
Figure 3-3