Netgear WNDAP350 WNDAP350 User Manual - Page 68

Maintenance, Remote Management, Read-Only Community Name, Trap Community Name - mib

Get Netgear WNDAP350 - ProSafe 802.11n Dual Band Wireless Access Point PDF manuals and user guides
UPC - 606449064643
View all Netgear WNDAP350 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 68 highlights

ProSafe Dual Band Wireless-N Access Point WNDAP350 Reference Manual To set up an SNMP management interface: 1. Under the Maintenance tab, select Remote Management, and then select SNMP from the left sidebar. The SNMP screen displays, as shown in Figure 3-1 below: Figure 3-1 Configure SNMP settings 2. Enter the following information in the SNMP fields: • SNMP: Enable SNMP to allow the SNMP network management software, such as HP OpenView, to manage the wireless access point via SNMPv1/v2 protocol. • Read-Only Community Name: The community string to allow the SNMP manager to read the wireless access point's MIB objects. The default is Public. • Read-Write Community Name: The community string to allow the SNMP manager to read and write the wireless access point's MIB objects. The default is Private. • Trap Community Name: The community string to allow the SNMP manager to send traps. The default is trap. • IP address to Receive Traps: The IP address of the SNMP manager to receive traps sent from the wireless access point. • Trap Port: The port number on which the SNMP Manager will receive traps. The default is 162/UDP. 3-2 Management v1.1, November 2009

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
ProSafe Dual Band Wireless-N Access Point WNDAP350 Reference Manual
3-2
Management
v1.1, November 2009
To set up an SNMP management interface:
1.
Under the
Maintenance
tab, select
Remote Management
, and then select
SNMP
from the
left sidebar. The SNMP screen displays, as shown in
Figure 3-1
below:
2.
Enter the following information in the SNMP fields:
•
SNMP:
Enable SNMP to allow the SNMP network management software, such as HP
OpenView, to manage the wireless access point via SNMPv1/v2 protocol.
•
Read-Only Community Name:
The community string to allow the SNMP manager to
read the wireless access point's MIB objects. The default is Public.
•
Read-Write Community Name:
The community string to allow the SNMP manager to
read and write the wireless access point's MIB objects. The default is Private.
•
Trap Community Name:
The community string to allow the SNMP manager to send
traps. The default is trap.
•
IP address to Receive Traps:
The IP address of the SNMP manager to receive traps sent
from the wireless access point.
•
Trap Port
: The port number on which the SNMP Manager will receive traps. The default
is 162/UDP.
Figure 3-1
Configure SNMP settings