Nokia IP1260 Installation Guide - Page 138

Configuring Software to Use Hardware Acceleration, To secure the connections

Get Nokia IP1260 - Security Appliance PDF manuals and user guides View all Nokia IP1260 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 138 highlights

8 Installing and Replacing Other Components The two sets of connectors should be aligned with each other. The four screw holes and four standoffs should also be aligned with each other. 6. Push down on the card until it is properly seated on the motherboard. 7. Place the screws through the standoff holes on the card and into the standoffs on the motherboard. Screw Accelerator card Standoff hole Motherboard standoff 8. Turn each screw clockwise to attach the card to the standoffs. Make sure that all four standoff connections are properly aligned before tightening the screws completely. 9. To secure the connections, tighten the screws firmly, but do not overtighten. 10. Slide the chassis assembly back into the appliance and resecure the four retaining screws. Reseating the chassis assembly automatically restores power to the appliance. 11. Configure your software to use hardware acceleration by following the instructions in "Configuring Software to Use Hardware Acceleration" on page 139. 138 Nokia IP1200 Series Security Platform Installation Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
8
Installing and Replacing Other Components
138
Nokia IP1200 Series Security Platform Installation Guide
The two sets of connectors should be aligned with each other. The four
screw holes and four standoffs should also be aligned with each other.
6.
Push down on the card until it is properly seated on the motherboard.
7.
Place the screws through the standoff holes on the card and into the
standoffs on the motherboard.
8.
Turn each screw clockwise to attach the card to the standoffs.
Make sure that all four standoff connections are properly aligned before
tightening the screws completely.
9.
To secure the connections, tighten the screws firmly, but do not
overtighten.
10.
Slide the chassis assembly back into the appliance and resecure the four
retaining screws.
Reseating the chassis assembly automatically restores power to the
appliance.
11.
Configure your software to use hardware acceleration by following the
instructions in
“Configuring Software to Use Hardware Acceleration”
on
page 139.
Screw
Accelerator card
Standoff hole
Motherboard standoff