Sony HDWM2000/20 Operation Manual - Page 111
Items in the Basic Setup Menu
View all Sony HDWM2000/20 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 111 highlights
10-3 Items in the Basic Setup Menu The basic setup menu contains the following items. In the "Settings" column of the table, the factory default settings are indicated by an enclosing box. Item number Item name Settings 001 PREROLL TIME 0S ... 5S ... 30S: Set the preroll time to between 0 and 30 seconds. A preroll time of at least 5 seconds is recommended when using this unit for editing. 002a) 003a), b) 004 005 CHARACTER HPOSITION CHARACTER VPOSITION SYNCHRONIZE DISPLAY INFORMATION SELECT Adjust the horizontal screen position of the character information output from the COMPOSITE VIDEO OUTPUT 3 (SUPER) connector, HDSDI OUTPUT 3 (SUPER) connector, and SDI OUTPUT 3 (SUPER) connector for superimposed display on the monitor. 00 ... 1E ... 3C (59.94i, 29.97PsF, 23.98PsF mode)/00 ... 1B ... 36 (50i, 25PsF, 24PsF mode): The hexadecimal value 00 is for the far left of the screen and increasing the value moves the position of the characters to the right. Adjust the vertical screen position of the first line of the character information output from the COMPOSITE VIDEO OUTPUT 3 (SUPER) connector, HDSDI OUTPUT 3 (SUPER) connector, and SDI OUTPUT 3 (SUPER) connector for superimposed display on the monitor. 00 ... 57 ... 6C (59.94i, 29.97PsF, 23.98PsF mode)/00 ... 70 ... 88 (50i, 25PsF, 24PsF mode): The hexadecimal value 00 is for the top of the screen and increasing the value lowers the position of the characters. When editing using this unit as a controller and an external VTR connected to this unit via a 9-pin remote control cable, this item determines whether or not to operate the two units in phase synchronization. OFF: Do not operate in phase synchronization. ON : Operate in phase synchronization. Determines the kind of character information to be output from the COMPOSITE VIDEO OUTPUT 3 (SUPER) connector, HDSDI OUTPUT 3 (SUPER) connector, and SDI OUTPUT 3 (SUPER) connector when the function menu item CHARA is set to ON. T&STA : Time data display information and the unit's status T&UB: Time data display information and the user's bits T&CTL: Time data display information and CTL T&T: Time data display information and time code (LTC or VITC) TIME: Time code (LTC or VITC) only If there is an overlap between the setting of this item and the setting of the control panel, it is automatically avoided. For example, if CTL is selected on the control panel and this menu item setting is T&CTL, then CTL and LTC are output. 006 LOCAL FUNCTION Determines which buttons on the control panel are enabled when this unit is ENABLE controlled from external equipment. DIS: All buttons and switches are disabled. S&E&F : Only the STOP button, EJECT button, and F1 to F6 buttons are enabled. ENA: All buttons and switches except the RECORDER button and PLAYER button are enabled. MAP: Follow the LOCAL KEY MAP setting. For information about setting the LOCAL KEY MAP, see menu item 023 (LOCAL KEY MAP) (page 10-9). 007 TAPE TIMER DISPLAY Determines whether to display the CTL count in 12-hour mode or 24-hour mode. + -12H : 12-hour mode 24H: 24-hour mode 008 MONITORING For recorder-player editing with only one monitor connected to the recorder, SELECTION FOR VTR- determines whether the recorder is forced into E-E mode when the recorder's TO-VTR EDIT PLAYER button is pressed to view the player's playback signals on the monitor. MANU : Do not force the recorder into E-E mode. AUTO: Force the recorder into E-E mode. a) When setting items 002 and 003, watch the monitor screen, and adjust to the required state. b) Note When displaying time code values, there is a slight time delay. Therefore, when creating a tape for off-line editing, the information inserted in the upper half of the screen may be delayed by one frame. (Continued) 10-7 Chapter 10 Setup Menus Chapter 10 Setup Menus