Sony HDWM2000/20 Operation Manual - Page 2

WARNING

To prevent fire or shock hazard, do not

expose the unit to rain or moisture.

To avoid electrical shock, do not open

the cabinet.

Refer servicing to qualified

personnel only.

THIS APPARATUS MUST BE EARTHED.

AVERTISSEMENT

Afin d’éviter tout risque d’incendie ou

d’électrocution, ne pas exposer cet

appareil à la pluie ou à l’humidité.

Afin d’écarter tout risque d’électrocution,

garder le coffret fermé. Ne confier

l’entretien de l’appareil qu’à un

personnel qualifié.

CET APPAREIL DOIT ÊTRE RELIÉ À LA

TERRE.

WARNUNG

Um Feuergefahr und die Gefahr eines

elektrischen Schlages zu vermeiden, darf

das Gerät weder Regen noch

Feuchtigkeit ausgesetzt werden.

Um einen elektrischen Schlag zu

vermeiden, darf das Gehäuse nicht

geöffnet werden.

Überlassen Sie

Wartungsarbeiten stets nur qualifiziertem

Fachpersonal.

DIESES GERÄT MUSS GEERDET

WERDEN.

This symbol is intended to alert the user to

the presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the appliance.

For the customers in the U.S.A.

This equipment has been tested and found to comply with

the limits for a Class A digital device, pursuant to Part 15 of

the FCC Rules.

These limits are designed to provide

reasonable protection against harmful interference when

the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful

interference to radio communications.

Operation of this

equipment in a residential area is likely to cause harmful

interference in which case the user will be required to

correct the interference at his own expense.

You are cautioned that any changes or modifications not

expressly approved in this manual could void your authority

to operate this equipment.

The shielded interface cable recommended in this manual

must be used with this equipment in order to comply with

the limits for a digital device pursuant to Subpart B of Part

15 of FCC Rules.

WARNING:

THIS WARNING IS APPLICABLE FOR USA

ONLY.

If used in USA, use the UL LISTED power

cord specified below.

DO NOT USE ANY OTHER POWER CORD.

Plug Cap

Parallel blade with ground pin

(NEMA 5-15P Configuration)

Cord

Type SJT, three 16 or 18 AWG

wires

Length

Less than 2.5 m (8 ft 3 in)

Rating

Minimum 10 A, 125 V

Using this unit at a voltage other than 120V

may require the use of a different line cord or

attachment plug, or both.

To reduce the risk of fire or electrical shock,

refer servicing to qualified service personnel.

Section	Page
Table of Contents	5
Chapter 1 Overview	7
1-1 Features	7
1-2 Example System Configuration	10
Chapter 2 Location and Function of Parts	11
2-1 Control Panels	11
2-1-1 Upper Control Panel	12
2-1-2 Lower Control Panel	13
2-1-3 Switch Panel	24
2-2 Connector Panel	25
Chapter 3 Preparations	31
3-1 Connections to External Devices	31
3-1-1 Connections to Digital Devices	31
3-2 Reference Sync Signals	32
3-2-1 Selecting Reference Signal Depending on Operational Status	32
3-2-2 Connecting Reference Signals	33
3-3 Setup	35
3-4 Superimposed Character Information	36
3-5 Cassettes	38
3-5-1 Cassette Types	38
3-5-2 Inserting and Ejecting Cassettes	38
3-5-3 Preventing Accidental Erasure of Recordings	39
3-6 Using a Memory Stick	40
3-6-1 Notes on Memory Stick	40
Chapter 4 Recording and Playback	43
4-1 Recording	43
4-1-1 Preparations for Recording	43
4-1-2 Recording Time Code and User Bit Values	44
4-1-3 Recording Procedure	46
4-2 Playback	47
4-2-1 Preparations for Playback	47
4-2-2 Playback Procedures	48
4-2-3 Dynamic Motion Control (DMC) Playback	52
Chapter 5 Editing	55
5-1 Automatic Editing	55
5-1-1 Overview	55
5-1-2 Switch and Menu Settings	56
5-1-3 Selecting the Editing Mode	57
5-1-4 Setting Edit Points	57
5-1-5 Modifying and Deleting Edit Points	60
5-1-6 Cue-up to Edit Points and Preroll	61
5-1-7 Preview	61
5-1-8 Carrying Out Automatic Editing	62
5-2 DMC Editing	65
5-2-1 Overview of DMC Editing	65
5-2-2 Carrying Out DMC Editing	66
5-3 Special Automatic Editing Methods	67
5-3-1 Quick Editing	67
5-3-2 Continuous Editing	67
5-3-3 Standalone Editing	68
5-3-4 Manual Editing	68
5-3-5 Preread Editing	68
Chapter 6 Shot Mark Function	71
6-1 Overview	71
6-2 Shot Mark Operation Menu	72
6-3 Shot Mark Operations	73
6-3-1 Reading Shot Marks	73
6-3-2 Writing Shot Marks	73
6-3-3 Shot Mark List Operations	74
6-3-4 Cuing Up to Shot Marks	76
6-3-5 Reading In Shot Data	77
6-3-6 Sorting Shot Marks	78
Chapter 7 Tele-File	79
7-1 Overview of Tele-File Functions	79
7-2 Opening the Tele-File Menu	80
7-3 Tele-File Menu	81
7-3-1 Clip Data Display	81
7-3-2 Preroll and Cue Up Using Clip Data	84
7-3-3 Modifying Clip Data	85
7-3-4 Undo/Resume Functions	88
7-3-5 Displaying and Modifying Attribute Data	89
Chapter 8 UMID Functions	91
8-1 Overview of UMID Functions	91
8-2 Recording UMIDs	92
8-3 UMID Output and Display	94
8-3-1 UMID Output Settings	94
8-3-2 UMID Display	94
Chapter 9 Function Menu	97
9-1 Overview	97
9-1-1 Function Menu Configuration	97
9-1-2 Using the Function Menu	98
9-2 Function Menu Item List	99
Chapter 10 Setup Menus	105
10-1 Setup Menu Configuration	105
10-2 Setup Menu Operations	106
10-3 Items in the Basic Setup Menu	111
10-4 Items in the Extended Setup Menu	114
Chapter 11 Maintenance and Inspection	139
11-1 Removing a Cassette When Tape Slack Occurs	139
11-2 Head Cleaning	139
11-3 Error Messages	140
11-4 Moisture Condensation	142
11-5 Regular Checks	143
11-5-1 Digital Hours Meter	143
11-5-2 Maintenance Timings	144
Appendix	145
Specifications	145

Sony HDWM2000/20 Operation Manual - Page 2

Warning, Avertissement, Cet Appareil Doit Être ReliÉ À La - manual

Page 2 highlights