Home » Sony Manuals » Voice Recorders » Sony HDWM2000/20 » Manual Viewer

Sony HDWM2000/20 Operation Manual - Page 38

Cassettes, 3-5-1 Cassette Types, 3-5-2 Inserting and Ejecting Cassettes, Inserting and Ejecting - hdw m2000 manual

View all Sony HDWM2000/20 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 38 highlights

Chapter 3 Preparations 3-5 Cassettes 3-5-1 Cassette Types This unit uses the following HDCAM cassettes for both recording and playback. HDCAM cassettes Small cassettes BCT-6HD/12HD/22HD/32HD/40HD Large cassettes BCT-34HDL/64HDL/94HDL/124HDL The HDW-M2000/M2000P can also play back the following cassettes. • Digital Betacam cassettes • MPEG IMX cassettes • Betacam SX cassettes • Betacam SP cassettes (metal tape) • Betacam cassettes (oxide tape) 1 Turn the POWER switch on. 2 Check the following points, then insert the cassette in the orientation shown in the figure. • Check that message "ERR-10" is not shown in the time data/menu display section. • Check that there is no slack in the tape. The cassette is drawn into the unit, and the STANDBY and STOP buttons light. Removing slack from the tape Press in one of the reels with a finger, and turn gently in the direction shown by the arrows until there is no slack in the tape. 3-5-2 Inserting and Ejecting Cassettes It is not possible to insert or eject a cassette unless the unit is powered on. Inserting a cassette EJECT button 1 2 Small cassette Ejecting a cassette Press the EJECT button. Note Ejecting is a local operation. It is not possible to eject a cassette in another unit by remote control. If the tape slacks inside the unit, pressing the EJECT button may not eject the cassette. For information about how to remove the cassette in such a case, refer to Section 1-17 in the Installation Manual. STANDBY REW PLAY F FWD STOP Large cassette STANDBY button STOP button 3-8 Chapter 3 Preparations

Section	Page
Table of Contents	5
Chapter 1 Overview	7
1-1 Features	7
1-2 Example System Configuration	10
Chapter 2 Location and Function of Parts	11
2-1 Control Panels	11
2-1-1 Upper Control Panel	12
2-1-2 Lower Control Panel	13
2-1-3 Switch Panel	24
2-2 Connector Panel	25
Chapter 3 Preparations	31
3-1 Connections to External Devices	31
3-1-1 Connections to Digital Devices	31
3-2 Reference Sync Signals	32
3-2-1 Selecting Reference Signal Depending on Operational Status	32
3-2-2 Connecting Reference Signals	33
3-3 Setup	35
3-4 Superimposed Character Information	36
3-5 Cassettes	38
3-5-1 Cassette Types	38
3-5-2 Inserting and Ejecting Cassettes	38
3-5-3 Preventing Accidental Erasure of Recordings	39
3-6 Using a Memory Stick	40
3-6-1 Notes on Memory Stick	40
Chapter 4 Recording and Playback	43
4-1 Recording	43
4-1-1 Preparations for Recording	43
4-1-2 Recording Time Code and User Bit Values	44
4-1-3 Recording Procedure	46
4-2 Playback	47
4-2-1 Preparations for Playback	47
4-2-2 Playback Procedures	48
4-2-3 Dynamic Motion Control (DMC) Playback	52
Chapter 5 Editing	55
5-1 Automatic Editing	55
5-1-1 Overview	55
5-1-2 Switch and Menu Settings	56
5-1-3 Selecting the Editing Mode	57
5-1-4 Setting Edit Points	57
5-1-5 Modifying and Deleting Edit Points	60
5-1-6 Cue-up to Edit Points and Preroll	61
5-1-7 Preview	61
5-1-8 Carrying Out Automatic Editing	62
5-2 DMC Editing	65
5-2-1 Overview of DMC Editing	65
5-2-2 Carrying Out DMC Editing	66
5-3 Special Automatic Editing Methods	67
5-3-1 Quick Editing	67
5-3-2 Continuous Editing	67
5-3-3 Standalone Editing	68
5-3-4 Manual Editing	68
5-3-5 Preread Editing	68
Chapter 6 Shot Mark Function	71
6-1 Overview	71
6-2 Shot Mark Operation Menu	72
6-3 Shot Mark Operations	73
6-3-1 Reading Shot Marks	73
6-3-2 Writing Shot Marks	73
6-3-3 Shot Mark List Operations	74
6-3-4 Cuing Up to Shot Marks	76
6-3-5 Reading In Shot Data	77
6-3-6 Sorting Shot Marks	78
Chapter 7 Tele-File	79
7-1 Overview of Tele-File Functions	79
7-2 Opening the Tele-File Menu	80
7-3 Tele-File Menu	81
7-3-1 Clip Data Display	81
7-3-2 Preroll and Cue Up Using Clip Data	84
7-3-3 Modifying Clip Data	85
7-3-4 Undo/Resume Functions	88
7-3-5 Displaying and Modifying Attribute Data	89
Chapter 8 UMID Functions	91
8-1 Overview of UMID Functions	91
8-2 Recording UMIDs	92
8-3 UMID Output and Display	94
8-3-1 UMID Output Settings	94
8-3-2 UMID Display	94
Chapter 9 Function Menu	97
9-1 Overview	97
9-1-1 Function Menu Configuration	97
9-1-2 Using the Function Menu	98
9-2 Function Menu Item List	99
Chapter 10 Setup Menus	105
10-1 Setup Menu Configuration	105
10-2 Setup Menu Operations	106
10-3 Items in the Basic Setup Menu	111
10-4 Items in the Extended Setup Menu	114
Chapter 11 Maintenance and Inspection	139
11-1 Removing a Cassette When Tape Slack Occurs	139
11-2 Head Cleaning	139
11-3 Error Messages	140
11-4 Moisture Condensation	142
11-5 Regular Checks	143
11-5-1 Digital Hours Meter	143
11-5-2 Maintenance Timings	144
Appendix	145
Specifications	145