Sony HVRM35U Product Manual (HVR-M35U Operating Manuals) - Page 89

Symptom Cause/Remedy A user bit is not displayed correctly during • When input video signals without a user bit are recorded while HDV is input via fast-forward/rewind. i.LINK, the user bit is not displayed correctly. Either or "00 00 00 00" is displayed during playback and fast-forward/rewind, respectively. appears on the date display (page 40). • The tape has been played back without setting the date and time. t Set the date and time. • The tape portion being played back has no recording. • If there is a scratch or noise on the tape, the data code cannot be read. Although the SDI cable or component video cable is connected properly to a television set or monitor to play back a tape, no image or audio is output. t Use the correct setting for [SDI/CMPNT] in [VIDEO OUT] in the [IN/OUT REC] menu depending on the equipment connected. • No audio is output from the COMPONENT OUT jacks. t Connect an audio cable. When you connect the unit to a 4:3 television set, the displayed image appears flattened. t When you output from the HD/SD SDI OUT jack and COMPONENT OUT jacks, set [SDI/CMPNT] and [DOWN CONVERT] of [VIDEO OUT] in the [IN/ OUT REC] menu correctly before playback. When you output from the HDV/ DV jack, set [HDV t DV CONV] and [DOWN CONVERT] of [i.LINK SET] in the [IN/OUT REC] menu correctly before playback. When you output from the S VIDEO jack and VIDEO jack, set [DOWN CONVERT] of [VIDEO OUT] in the [IN/OUT REC] menu correctly before playback. t Before playback of DVCAM (DV) format images recorded in the wide mode to be output via the COMPONENT OUT jack, S VIDEO OUT jack, or VIDEO OUT jack, set [DV WIDE CONV] of [VIDEO OUT] in the [IN/OUT REC] menu properly. Even though [HDV/DV IN TC] in the [TC/ UB SET] menu is set to [EXTERNAL], the time code of the input i.LINK signal is not recorded. • The i.LINK signal output from the digital non-linear editing controller does not include a time code. t Confirm that the editing software you are using is capable of outputting a time code. • The INPUT SELECT switch is not set to HDV/DV. t Set it to HDV/DV. After playing at 1/10 of normal speed in • To protect a tape, the unit is set to start normal playback after playing at 1/10 of forward or reverse for more than 1 minute, normal speed in forward or reverse for more than 1 minute. normal playback forward starts. t Play back the tape at 1/3 of normal speed in forward or reverse. Playback pause mode is released and the unit goes into the stop mode. • To protect the tape, the unit is set to go into the stop mode after the playback pause mode continues for a certain period. t Set [FROM STILL] in the [VTR SET] menu to [STEP FORWARD]. If you do so, the tape will forward by one frame for each time interval set in [STILL TIME]. Playback pause mode is released and the • To protect the tape, the unit is set to forward the tape after the playback pause tape forwards for each preset time interval. mode continues for a certain period. t Set [FROM STILL] in the [VTR SET] menu to [STOP]. If you do so, the unit goes into the stop mode after the playback pause mode continues for the interval set in [STILL TIME]. After the unit has been left in the stop mode and no key operations have been attempted for more than one hour, the unit goes into the standby mode (the unit's power turns off). • [AUTO STANDBY] in the [OTHERS] menu is set to [ON]. t Set [AUTO STANDBY] to [OFF]. The pause mode of playback, recording, or • To protect the tape and the video heads, the unit goes into the stop mode after audio dubbing is released automatically. the pause mode of recording, audio dubbing, or duplicating continues for more than 3 minutes. t To maintain the pause mode, set [FROM REC P] in the [VTR SET] menu to [REC PAUSE]. Chapter 6 Maintenance (Continued) 89 Chapter 6 Maintenance