Xerox 8560DN User Guide - Page 22

Automatically Setting the Printer’s IP Address, Using the Control Panel, Using CentreWare IS

Get Xerox 8560DN - Phaser Color Solid Ink Printer PDF manuals and user guides
UPC - 095205733280
View all Xerox 8560DN manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

Configuring the Network Address Automatically Setting the Printer's IP Address If the printer is connected to a small established TCP/IP network without a DHCP server, use the installer on the Software and Documentation CD-ROM to detect or assign an IP address to your printer. For further instructions, insert the Software and Documentation CD-ROM into your computer's CD-ROM drive. After the Installer launches, follow the prompts for installation. Note: For the automatic Installer to function, the printer must be connected to an established TCP/IP network. Dynamic Methods of Setting the Printer's IP Address There are two protocols available for dynamically setting the printer's IP address: ■ DHCP (enabled by default on all printers) ■ AutoIP You can turn on/off both protocols using the control panel, or use CentreWare IS to turn on/off DHCP. Note: You can view the printer's IP address at any time. On the control panel, select Information, press the OK button, select Printer Identification, and then press the OK button. Using the Control Panel To turn on/off either the DHCP or AutoIP protocol: 1. On the control panel, select Printer Setup, and then press the OK button. 2. Select Connection Setup, and then press the OK button. 3. Select Network Setup, and then press the OK button. 4. Select TCP/IP Setup, and then press the OK button. 5. Select DHCP/BOOTP or AutoIP. 6. Press the OK button to run the selection On or Off. Using CentreWare IS To turn on/off the DHCP protocol: 1. Launch your web browser. 2. Enter the printer's IP address in the browser's Address field (http://xxx.xxx.xxx.xxx). 3. Select Properties. 4. Select the Protocols folder on the left navigation panel. 5. Select TCP/IP. 6. In the BOOTP/DHCP Settings section, set the BOOTP/DHCP option to On or Off. 7. Click the Save Changes button at the bottom of the page. Phaser® 8560 Color Printer 2-6

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
Configuring the Network Address
Phaser® 8560 Color Printer
2-6
Automatically Setting the Printer’s IP Address
If the printer is connected to a small established TCP/IP network without a DHCP server, use
the installer on the
Software and Documentation CD-ROM
to detect or assign an IP address to
your printer. For further instructions, insert the
Software and Documentation CD-ROM
into
your computer’s CD-ROM drive. After the Installer launches, follow the prompts for
installation.
Note:
For the automatic Installer to function, the printer must be connected to an established
TCP/IP network.
Dynamic Methods of Setting the Printer’s IP Address
There are two protocols available for dynamically setting the printer’s IP address:
■
DHCP (enabled by default on all printers)
■
AutoIP
You can turn on/off both protocols using the control panel, or use CentreWare IS to turn on/off
DHCP.
Note:
You can view the printer’s IP address at any time. On the control panel, select
Information
, press the
OK
button, select
Printer Identification
, and then press the
OK
button.
Using the Control Panel
To turn on/off either the DHCP or AutoIP protocol:
1.
On the control panel, select
Printer Setup
, and then press the
OK
button.
2.
Select
Connection Setup
, and then press the
OK
button.
3.
Select
Network Setup
, and then press the
OK
button.
4.
Select
TCP/IP Setup
, and then press the
OK
button.
5.
Select
DHCP/BOOTP
or
AutoIP
.
6.
Press the
OK
button to run the selection
On
or
Off
.
Using CentreWare IS
To turn on/off the DHCP protocol:
1.
Launch your web browser.
2.
Enter the printer’s IP address in the browser’s
Address
3.
Select
Properties
.
4.
Select the
Protocols
folder on the left navigation panel.
5.
Select
TCP/IP
.
6.
In the BOOTP/DHCP Settings section, set the
BOOTP/DHCP
option to
On
or
Off
.
7.
Click the
Save Changes
button at the bottom of the page.