Brother International DCP 8045D Network Users Manual - English - Page 118

addresses using BOOTP, DHCP or RARP your Brother Print/Fax, Unix/Linux Systems

Get Brother International DCP 8045D - B/W Laser - All-in-One PDF manuals and user guides
UPC - 012502610335
View all Brother International DCP 8045D manuals
Add to My Manuals
Save this manual to your list of manuals

Page 118 highlights

Unix/Linux Systems Typically, Unix systems require the colon ":" character between each digit of the Ethernet address. arp -s 192.189.207.2 00:80:77:31:01:07 You must be on the same Ethernet segment (that is, there cannot be a router between the Print/Fax server and operating system) to use the arp -s command. If there is a router, you may use BOOTP or other methods described in this chapter to enter the IP address. If your Administrator has configured the system to deliver IP addresses using BOOTP, DHCP or RARP your Brother Print/Fax server can receive an IP address from any one of these IP address allocation systems. In which case, you will not need to use the ARP command. The ARP command only works once. For security reasons, once you have successfully configured the IP address of a Brother Print/Fax server using the ARP command, you cannot use the ARP command again to change the address. The Print/Fax server will ignore any attempts to do this. If you wish to change the IP address again, use a Web Browser, the machine's control panel or factory reset the Print/Fax server (which will then allow you to use the ARP command again). To configure the Print/Fax server and to verify the connection, enter the following command ping ipaddress where ipaddress is the IP address of the Print/Fax server. For example, ping 192.189.207.2. TCP/IP CONFIGURATION 11 - 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
TCP/IP CONFIGURATION 11 - 7
Unix/Linux Systems
Typically, Unix systems require the colon “
:
” character between
each digit of the Ethernet address.
arp -s 192.189.207.2 00:80:77:31:01:07
To configure the Print/Fax server and to verify the connection,
enter the following command
ping ipaddress
where
ipaddress
is the IP address of the Print/Fax server. For
example,
ping 192.189.207.2
.
You must be on the same Ethernet segment (that is, there cannot
be a router between the Print/Fax server and operating system) to
use the arp -s command.
If there is a router, you may use BOOTP or other methods
described in this chapter to enter the IP address.
If your Administrator has configured the system to deliver IP
addresses using BOOTP, DHCP or RARP your Brother Print/Fax
server can receive an IP address from any one of these IP
address allocation systems. In which case, you will not need to
use the ARP command. The ARP command only works once. For
security reasons, once you have successfully configured the IP
address of a Brother Print/Fax server using the ARP command,
you cannot use the ARP command again to change the address.
The Print/Fax server will ignore any attempts to do this. If you wish
to change the IP address again, use a Web Browser, the
machine’s control panel or factory reset the Print/Fax server
(which will then allow you to use the ARP command again).