Brother International MFC-660MC Users Manual - English - Page 19

Fax Tones and Handshake, ECM (Error Correction Mode), When your FAX/MFC answers in FAX/TEL Mode

Get Brother International MFC-660MC PDF manuals and user guides View all Brother International MFC-660MC manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

Fax Tones and Handshake When someone is sending a fax, the FAX/MFC sends fax calling tones (CNG tones)- soft, intermittent beeps at 4-second intervals. You'll hear them when you dial and press Start, and they continue for about 40 seconds after dialing. During that time, the sending machine must begin the "handshake" with the receiving machine. Each time you use automatic procedures to send a fax, you are sending CNG tones over the phone line. You'll soon learn to listen for these soft beeps each time you answer a phone on your fax line, so you know if you are receiving a fax message. The receiving fax responds with fax receiving tones-loud, chirping sounds. A receiving fax chirps for about 40 seconds over the phone line, and the screen displays RECEIVE. If your FAX/MFC is set to the FAX ONLY Mode, it will answer every call automatically with fax receiving tones. Even if the other party hangs up, your FAX/MFC continues to send the "chirps" for about 40 seconds, and the screen continues to display "RECEIVE". To cancel the receiving mode, press Stop. When your FAX/MFC answers in FAX/TEL Mode, the FAX/MFC listens for CNG tones and then responds with receiving tones. The fax "handshake" is the time in which the sending machine's CNG tones and the receiving machines "chirps" overlap. This must be for at least 2 to 4 seconds, so the machines can understand how each is sending and receiving the fax. The handshake cannot begin until the call is answered, and the CNG tones only last for about 40 seconds after the number is dialed. Therefore, it's important for the receiving machine to answer the call in as few rings as possible. When you have an external telephone answering device (TAD) on your fax line, your TAD will determine the number of rings before the call is answered. Pay special attention to the directions in the Installation chapter for connecting a TAD to your FAX/MFC. ECM (Error Correction Mode) The Error Correction Mode (ECM) is a way for the FAX/MFC to check the integrity of a fax transmission while it is in progress. ECM transmissions are possible only between machines that both have the ECM feature. If they do, you may send and receive fax messages that are continuously checked for their integrity. Sufficient memory must be available in your FAX/MFC for this feature to work. INTRODUCTION 1-2

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
INTRODUCTION
1 - 2
Fax Tones and Handshake
When someone is sending a fax, the FAX/MFC sends fax calling tones (CNG tones)—
soft, intermittent beeps at 4-second intervals. You’ll hear them when you dial and
press
Start
, and they continue for about 40 seconds after dialing. During that time, the
sending machine must begin the “handshake” with the receiving machine. Each time
you use automatic procedures to send a fax, you are sending CNG tones over the phone
line. You’ll soon learn to listen for these soft beeps each time you answer a phone on
your fax line, so you know if you are receiving a fax message.
The receiving fax responds with fax receiving tones—loud, chirping sounds. A
receiving fax chirps for about 40 seconds over the phone line, and the screen displays
RECEIVE. If your
FAX/MFC is set to the FAX ONLY Mode, it will answer every
call automatically with fax receiving tones. Even if the other party hangs up, your
FAX/MFC continues to send the “chirps” for about 40 seconds, and the screen
continues to display “RECEIVE”. To cancel the receiving mode, press
Stop
.
When your FAX/MFC answers in FAX/TEL Mode, the FAX/MFC listens for CNG
tones and then responds with receiving tones.
The fax “handshake” is the time in which the sending machine’s CNG tones and the
receiving machines “chirps” overlap. This must be for at least 2 to 4 seconds, so the
machines can understand how each is sending and receiving the fax. The handshake
cannot begin until the call is answered, and the CNG tones only last for about 40
seconds after the number is dialed. Therefore, it’s important for the receiving machine
to answer the call in as few rings as possible.
ECM (Error Correction Mode)
The Error Correction Mode (ECM) is a way for the FAX/MFC to check the integrity
of a fax transmission while it is in progress. ECM transmissions are possible only
between machines that both have the ECM feature. If they do, you may send and
receive fax messages that are continuously checked for their integrity.
Sufficient memory must be available in your FAX/MFC for this feature to work.
When you have an external telephone answering device (TAD) on your fax line, your
TAD will determine the number of rings before the call is answered. Pay special
attention to the directions in the Installation chapter for connecting a TAD to your
FAX/MFC.