Canon CR-N500 Remote Camera Settings Guide - Page 57

[System] > [Server] > [RTP], RTP Server, Audio Settings

Get Canon CR-N500 PDF manuals and user guides View all Canon CR-N500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 57 highlights

[System] > [Server] > [RTP] Settings for video and audio streaming using RTP. RTP Server Settings for use of RTP, RTSP authentication method and port number. [RTP] Select whether to use RTP. [RTSP Authentication Method] Select a RTSP authentication method. Since RTSP authentication method is set independently from HTTP Server authentication method, it is necessary to configure the setting for each authentication method. [RTSP Port] Enter the RTSP port. In general, use [554] (factory default settings). Audio Settings Settings for multicast audio transmission. [Audio Compression Method] Displays the audio compression method and the frequency. [AAC-LC 48kHz] as fixed value. [Multicast Address] Enter multicast address for audio transmission as follows. IPv4: in the range of 224.0.0.0 to 239.255.255.255 IPv6: address starting with ff00::/8 [Multicast Port] Enter multicast port for audio transmission. [Multicast TTL] Enter the effective range for multicast distribution. The TTL (Time To Live), representing the effective range for multicast distribution, is decremented each time the signal passes through a router. When it reaches 0, distribution through a router becomes impossible. For example, if TTL is set to [1], multicast distribution is confined to the local segment only and cannot pass through the router. Note With one of the following settings, audio multicast distribution is disabled. - Set [0.0.0.0] (IPv4) or [::0(::)] (IPv6) for [Multicast Address] . - Set [0] for [Multicast Port] or [Multicast TTL]. 57

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
57
Settings for video and audio streaming using RTP.
RTP Server
Settings for use of RTP, RTSP authentication method and port number.
[RTP]
Select whether to use RTP.
[RT
S
P Authentication Method]
Select a RTSP authentication method. Since RTSP authentication method is set independently from HTTP Server
authentication method, it is necessary to configure the setting for each authentication method.
[RT
S
P Port]
Enter the RTSP port.
In general, use [554] (factory default settings).
Audio Settings
Settings for multicast audio transmission.
[Audio Compression Method]
Displays the audio compression method and the frequency. [AAC-LC 48kHz] as fixed value.
[Multicast Address]
Enter multicast address for audio transmission as follows.
IPv4: in the range of 224.0.0.0 to 239.255.255.255
IPv6: address starting with ff00::/8
[Multicast Port]
Enter multicast port for audio transmission.
[Multicast TTL]
Enter the effective range for multicast distribution.
The TTL (Time To Live), representing the effective range for multicast distribution, is decremented each time the signal
passes through a router. When it reaches 0, distribution through a router becomes impossible.
For example, if TTL is set to [1], multicast distribution is confined to the local segment only and cannot pass through the
router.
Note
With one of the following settings, audio multicast distribution is disabled.
–
Set [0.0.0.0] (IPv4) or [::0(::)] (IPv6) for [Multicast Address] .
–
Set [0] for [Multicast Port] or [Multicast TTL].
[System] > [Server] > [RTP]