Canon CR-N500 Remote Camera Settings Guide - Page 58

RTP Mainstream, RTP Substream 1

Get Canon CR-N500 PDF manuals and user guides View all Canon CR-N500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 58 highlights

RTP Mainstream, RTP Substream 1, RTP Substream 2 Settings for RTP stream distribution, to be configured for each stream. [Video Type] Displays [Video Codec] and [Video Size] set for each video stream in [System] > [Video and Audio] > [IP Streaming Video]. [Multicast Address] Enter multicast address for RTP stream as follows. IPv4: in the range of 224.0.0.0 to 239.255.255.255 IPv6: address starting with ff00::/8 [Multicast Port] Enter multicast port for RTP stream. [Multicast TTL] Enter the effective range for multicast distribution of RTP stream. The TTL (Time To Live), representing the effective range for multicast distribution, is decremented each time the signal passes through a router. When it reaches 0, distribution through a router becomes impossible. For example, if TTL is set to [1], multicast distribution is confined to the local segment only and cannot pass through the router. [Audio Transmission] Select whether to use the audio transmission of RTP stream. When [Disable] is set for [System] > [Video and Audio] > [Audio] > [General Audio] > [Audio Input], [Enable] cannot be set. Note • With one of the following settings, the multicast distribution of RTP stream is disabled. - Set [0.0.0.0] (IPv4) or [::0(::)] (IPv6) for [Multicast Address] . - Set [0] for [Multicast Port] or [Multicast TTL]. • URL for RTP stream rtsp://IP address: port/rtpstream/config1(to 3) Example: rtsp://192.168.100.1:554/rtpstream/config1 Note: Distribution method depends on the request for distribution from the RTP client application. - Distribution method depends on the request for distribution from the RTP client application. - config1 requests the distribution of Mainstream, config 2 requests Substream 1, and config 3 requests Substream 2. • Video quality of [Bit Rate Control] of Main and Sub1 uses the settings in [System] > [Video and Audio] > [IP Streaming Video] (P. 52) • [Video Distribution] in [System]> [Security]> [User Management]> [User Authority] is not reflected in RTP. • In an environment using proxy server or firewall, the video from the RTP stream may not be displayed. In such a case, contact your system administrator. • When the host access restriction is applied to a client during the RTP over UDP stream distribution, it may take from a few seconds to several tens of seconds to stop the distribution. 58

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
58
RTP Mainstream, RTP Substream 1, RTP Substream 2
Settings for RTP stream distribution, to be configured for each stream.
[Video Type]
Displays [Video Codec] and [Video Size] set for each video stream in [System] > [Video and Audio] > [IP Streaming Video].
[Multicast Address]
Enter multicast address for RTP stream as follows.
IPv4: in the range of 224.0.0.0 to 239.255.255.255
IPv6: address starting with ff00::/8
[Multicast Port]
Enter multicast port for RTP stream.
[Multicast TTL]
Enter the effective range for multicast distribution of RTP stream.
The TTL (Time To Live), representing the effective range for multicast distribution, is decremented each time the signal
passes through a router. When it reaches 0, distribution through a router becomes impossible.
For example, if TTL is set to [1], multicast distribution is confined to the local segment only and cannot pass through the
router.
[Audio Transmission]
Select whether to use the audio transmission of RTP stream.
When [Disable] is set for [System] > [Video and Audio] > [Audio] > [General Audio] > [Audio Input], [Enable] cannot be set.
Note
•
With one of the following settings, the multicast distribution of RTP stream is disabled.
–
Set [0.0.0.0] (IPv4) or [::0(::)] (IPv6) for [Multicast Address] .
–
Set [0] for [Multicast Port] or [Multicast TTL].
•
URL for RTP stream
rtsp://IP address: port/rtpstream/config1(to 3)
Example: rtsp://192.168.100.1:554/rtpstream/config1
Note: Distribution method depends on the request for distribution from the RTP client application.
–
Distribution method depends on the request for distribution from the RTP client application.
–
config1 requests the distribution of Mainstream, config 2 requests Substream 1, and config 3 requests Substream 2.
•
Video quality of [Bit Rate Control] of Main and Sub1 uses the settings in [System] > [Video and Audio] > [IP Streaming Video] (P. 52)
•
[Video Distribution] in [System]> [Security]> [User Management]> [User Authority] is not reflected in RTP.
•
In an environment using proxy server or firewall, the video from the RTP stream may not be displayed. In such a case, contact your
system administrator.
•
When the host access restriction is applied to a client during the RTP over UDP stream distribution, it may take from a few seconds to
several tens of seconds to stop the distribution.