Canon CR-N500 Remote Camera Settings Guide - Page 64

[System] > [Communication] > [External Connection (IP)], Standard Communication (IP), NDI|HX

Page 64 highlights

[System] > [Communication] > [External Connection (IP)] Settings for communication for connecting controllers, etc. via IP. Standard Communication (IP) Settings for operating the cameras from the controller connected by the standard IP communication. [Standard Communication (IP)] Select whether to use [Standard Communication (IP)] for the connection with the controller. [Response Port Number] Select whether to use a fixed port number (52381) or a source port number when communicating with the controller. [Camera IP Settings Inquiry] Select whether to allow the inquiry on the camera IP settings from the controller. [Camera IP Settings Network Settings] Select whether to allow to change the network settings of the camera from the controller. NDI|HX Settings for exchanging data with NDI|HX supported devices. [NDI|HX] Select whether to use [NDI|HX] as the communication protocol. For setting to [Enable], go to [System] > [Communication] > [Network] > [mDNS] and select [Enable] (P. 61). Note When [System] > [Video and Audio] > [IP Streaming Video] > [Mainstream] >[Video Codec] is set to [H.265], NDI|HX cannot be used. [Audio Transmission] Select whether to use the audio transmission. When [Disable] is set for [System] > [Video and Audio] > [Audio] > [General Audio] > [Audio Input], [Enable] cannot be set. [Discovery Server] Select whether to use the Discovery Server. When set to [Enable], it notifies the Discovery Server only of the IP address and does not notify other hosts of the IP address nor hostname. [Discovery Server IP Address] Enter the IP address of the Discovery Server. [Multicast Distribution] Select whether to use the multicast distribution. 64

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119

64
Settings for communication for connecting controllers, etc. via IP.
Standard Communication (IP)
Settings for operating the cameras from the controller connected by the standard IP communication.
[
S
tandard Communication (IP)]
Select whether to use [Standard Communication (IP)] for the connection with the controller.
[Response Port Number]
Select whether to use a fixed port number (52381) or a source port number when communicating with the controller.
[Camera IP
S
ettings Inquiry]
Select whether to allow the inquiry on the camera IP settings from the controller.
[Camera IP
S
ettings Network
S
ettings]
Select whether to allow to change the network settings of the camera from the controller.
NDI|HX
Settings for exchanging data with NDI|HX supported devices.
[NDI
|
HX]
Select whether to use [NDI|HX] as the communication protocol.
For setting to [Enable], go to [System] > [Communication] > [Network] > [mDNS] and select [Enable] (P. 61).
Note
When [System] > [Video and Audio] > [IP Streaming Video] > [Mainstream] >[Video Codec] is set to [H.265], NDI|HX cannot be used.
[Audio Transmission]
Select whether to use the audio transmission.
When [Disable] is set for [System] > [Video and Audio] > [Audio] > [General Audio] > [Audio Input], [Enable] cannot be set.
[Discovery
S
erver]
Select whether to use the Discovery Server.
When set to [Enable], it notifies the Discovery Server only of the IP address and does not notify other hosts of the IP address
nor hostname.
[Discovery
S
erver IP Address]
Enter the IP address of the Discovery Server.
[Multicast Distribution]
Select whether to use the multicast distribution.
[System] > [Communication] > [External Connection (IP)]