Home » Canon Manuals » Video Cameras » Canon CR-N500 » Manual Viewer

Canon CR-N500 Remote Camera Settings Guide - Page 60

IPv6, DNS, IPv6 Default Gateway Address]

Add to My Manuals
Save this manual to your list of manuals

Page 60 highlights

Important When using IPv4 address settings in [Auto (DHCP)], in an environment with a router between the DHCP Server and the camera, IPv4 address may not be assigned correctly. In such a case, select [Manual] to set the fixed IPv4 address. [IPv4 Address] When [IPv4 Address Settings Method] is [Manual], enter the fixed IPv4 address. [Subnet Mask] When [IPv4 Address Settings Method] is [Manual], enter the subnet mask value specified for each network. [IPv4 Default Gateway Address] When [IPv4 Address Settings Method] is [Manual], enter a value. Make sure to set, when connecting the camera to a subnet different from IP connection device such as controller. [AutoIP] Select whether to use AutoIP. When the AutoIP address is enabled, IP address automatically set will be displayed in [IPv4 Address (AutoIP)]. IPv6 Settings for connection to the camera using IPv6. IPv6 address can be acquired automatically from the RA or the DHCPv6 Server, or can be set manually. Important Regarding [IPv6 Address (Manual)], [Prefix Length] and [IPv6 Default Gateway Address] for manual setting of IPv6, contact your system administrator. [IPv6] Select whether to use IPv6, [Auto (RA)] Select [Enable], when automatically setting the address using RA (Router Advertisement, network information transmitted automatically from the router). [Auto (DHCPv6)] Select [Enable], when automatically setting the address using DHCPv6. [IPv6 Address (Manual)] For setting the address manually, enter a fixed IPv6 address. [Prefix Length] For setting the address manually, enter a prefix length. [IPv6 Default Gateway Address] For setting the address manually, enter a default gateway address. Make sure to set, when connecting the camera to a subnet different from IP connection device such as controller. [IPv6 Address (Auto)] When [IPv6] is [Enable] and [Auto (RA)] or [Auto (DHCPv6)] is [Enable], the address automatically acquired will be displayed. DNS Settings for the DNS Server address. DNS Server address can be set manually or can be acquired automatically from the DHCP/DHCPv6 Server. [Name Server Address 1], [Name Server Address 2] Enter the name server address to be registered. When only one address is to be registered, leave [Name Server Address 2] blank. 60

Section	Page
Introduction	2
Trademarks	2
Software License Agreement	2
Third Party Software	2
User Manuals	5
Types of User Manuals	5
How to Use This Document	5
Chapter 1 Before Use	11
Examples of System Configuration	12
Related Software	15
Camera Search Tool	15
Remote Camera Control Application	15
Security Checking/Settings	16
Checking the Firewall Settings	16
Initial Camera Settings	17
Settings using the Camera Search Tool	17
Camera's Settings Page from the Web Browser	19
Chapter 2 Camera Setup	20
Overview	21
Accessing from a Web Browser	21
Configuration of the Settings Page	23
Camera Operation	25
Operation by Clicking on the Video Display Area or by Slider	25
Exposure Settings	27
WB/Color Settings	31
Image Quality Settings	33
Image Quality Details Settings	35
Focus Settings (CR-N500)	37
Autofocus	37
Manual Focus	40
Focus Settings (CR-N300)	42
Autofocus	42
Manual Focus	44
PTZ/IS Settings	45
Preset Settings	46
Registering Presets	46
Calling Presets	47
Deleting Presets	47
System Settings	48
Screen Configuration	48
Setting Items	49
Common Operations	49
[System] > [Video and Audio] > [HDMI/SDI]	51
HDMI/SDI	51
SDI	51
[System] > [Video and Audio] > [IP Streaming Video]	52
Mainstream	52
Substream 1	53
Substream 2	53
[System] > [Video and Audio] > [Audio]	54
General Audio	54
IP Audio Streaming	55
[System] > [Server] > [HTTP/Video]	56
HTTP Server	56
Video Server	56
[System] > [Server] > [RTP]	57
RTP Server	57
Audio Settings	57
RTP Mainstream, RTP Substream 1, RTP Substream 2	58
[System] > [Communication] > [Network]	59
LAN	59
IPv4	59
IPv6	60
DNS	60
mDNS	61
[System] > [Communication] > [Wireless LAN]	62
Interface	62
Access Point	62
IPv4	62
[System] > [Communication] > [External Connection (IP)]	64
Standard Communication (IP)	64
NDI\|HX	64
RTMP	65
[System] > [Communication] > [External Connection (Serial)]	66
Serial Port	66
Standard Communication (Serial)	67
[System] > [Security] > [Certificate Management]	68
Server Certificate Management	68
Create Certificate	68
[System] > [Security] > [SSL/TLS]	69
Encrypted Communications	69
Server Certificate	69
[System] > [Security] > [User Management]	70
Administrator Account	71
Authorized User Account	71
User Authority	71
[System] > [Security] > [Host Access Restrictions]	72
IPv4 Host Access Restrictions	72
IPv6 Host Access Restrictions	72
[System] > [System] > [Camera]	74
Camera Name	74
Installation Conditions	74
Tally Lamp	74
IR Remote Controller	75
Genlock	75
[System] > [System] > [Date and Time]	76
Current Date and Time	76
Settings	76
[System] > [System] > [Environment]	78
Environment	78
[System] > [System] > [Language]	79
Language	79
[System] > [Maintenance] > [General]	80
Device Information	80
Tool	80
Initialization	80
[System] > [Maintenance] > [Backup/Restore]	82
Backup/Restore	82
[System] > [Maintenance] > [Update Firmware]	83
Device Information	83
Update Firmware	83
[System] > [Maintenance] > [Log]	84
View Logs	84
Chapter 3 IR Remote Controller	85
Names and Functions of Parts	86
Handling the Remote Controller	88
Chapter 4 Appendix	89
USB Camera Functions (CR-N300)	90
Image Adjustment/Camera Control Functions	90
Troubleshooting	91
List of Log Messages	93
Log Messages on the Camera	93
Error Log	93
Warning log	95
Notification log	96
Restoring to the Factory Default Settings	100
Restoring to the Initial Settings from a Web Browser	100
Restoring to the Factory Default Settings with the RESET Switch on the Camera	100
List of Factory Default Settings	102
Routine Maintenance	105
Cleaning the External Surface	105
Cleaning the Lens	105
Specifications	106
CR-N500 Main Unit	106
CR-N300 Main Unit	108
Accessories	110
Operating Environment	110
Security Measures	112
Basic Measure 1: Setting Administrator Name and Password	113
Basic Measure 2: Using the Latest Firmware	113
Basic Measure 3: Setting Date and Time	113
Basic Measure 4: Monitoring the Log	113
Measures Suitable to the Users' Environment 1: User Management	114
Measures Suitable to the Users' Environment 2: Host Access Restrictions	114
Measures Suitable to the Users' Environment 3: Setting to the Digest Authentication	114
Measures Suitable to the Users' Environment 4: Changing the Port Number	115
Measures Suitable to the Users' Environment 5: Encrypting Communication	115
Measures Suitable to the Users' Environment 6: Disabling Unused Functions	115
Precautions When Disposing the Camera	116
Encrypting Backup Information	116

Match case Limit results 1 per page

[IPv4 Address]

When [IPv4 Address Settings Method] is [Manual], enter the fixed IPv4 address.

[

ubnet Mask]

When [IPv4 Address Settings Method] is [Manual], enter the subnet mask value specified for each network.

[IPv4 Default Gateway Address]

When [IPv4 Address Settings Method] is [Manual], enter a value. Make sure to set, when connecting the camera to a subnet

different from IP connection device such as controller.

[AutoIP]

Select whether to use AutoIP. When the AutoIP address is enabled, IP address automatically set will be displayed in [IPv4

Address (AutoIP)].

IPv6

Settings for connection to the camera using IPv6. IPv6 address can be acquired automatically from the RA or the DHCPv6

Server, or can be set manually.

[IPv6]

Select whether to use IPv6,

[Auto (RA)]

Select [Enable], when automatically setting the address using RA (Router Advertisement, network information transmitted

automatically from the router).

[Auto (DHCPv6)]

Select [Enable], when automatically setting the address using DHCPv6.

[IPv6 Address (Manual)]

For setting the address manually, enter a fixed IPv6 address.

[Prefix Length]

For setting the address manually, enter a prefix length.

[IPv6 Default Gateway Address]

For setting the address manually, enter a default gateway address. Make sure to set, when connecting the camera to a

subnet different from IP connection device such as controller.

[IPv6 Address (Auto)]

When [IPv6] is [Enable] and [Auto (RA)] or [Auto (DHCPv6)] is [Enable], the address automatically acquired will be

displayed.

DNS

Settings for the DNS Server address. DNS Server address can be set manually or can be acquired automatically from the

DHCP/DHCPv6 Server.

[Name

erver Address 1], [Name

erver Address 2]

Enter the name server address to be registered. When only one address is to be registered, leave [Name Server Address 2]

blank.

Important

When using IPv4 address settings in [Auto (DHCP)], in an environment with a router between the DHCP Server and the camera, IPv4

address may not be assigned correctly. In such a case, select [Manual] to set the fixed IPv4 address.

Important

Regarding [IPv6 Address (Manual)], [Prefix Length] and [IPv6 Default Gateway Address] for manual setting of IPv6, contact your system

administrator.