Cisco AP541N-A-K9 Administration Guide - Page 165

Configuring the Wireless Distribution System, STEP 1

Get Cisco AP541N-A-K9 PDF manuals and user guides View all Cisco AP541N-A-K9 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 165 highlights

Configuration Examples Configuring the Wireless Distribution System 8 Wireless Radio Configuration Using SNMP STEP 1 Load the Cisco specific MIB module. STEP 2 From the MIB tree, navigate to the objects in the apRadio table (apRadioBss > apRadioTable). STEP 3 Use the apRadioStatus object to set the status of wireless Radio 1 to up (1). STEP 4 Use the apRadioMode object to set the wireless Radio 1 mode to IEEE 802.11b/g/ n, which is bg-n (4). STEP 5 Use the apRadioChannelPolicy object to set the channel policy to static (1), which disables the automatic channel assignment. STEP 6 Use the apRadioStaticChannel object to set the channel to 6. STEP 7 Use the apRadioChannelBandwith object to set the channel bandwidth for wireless Radio 1 to 40-MHz (2). STEP 8 Use the apRadioTxPower object to set the transmission power on wireless Radio 1 to 75. STEP 9 Navigate to the objects in the apBssTable. STEP 10 Use the apBssMaxStations object to set the value of the maximum allowed stations to 100. Configuring the Wireless Distribution System This example shows how to configure a WDS link between two APs. The local access point is MyAP1 and has a MAC address of 00:1B:E9:16:32:40, and the remote access point is MyAP2 with a MAC address of 00:30:AB:00:00:B0. The WDS link has the following settings, which must be configured on both APs: • Encryption: WPA (PSK) • SSID: wds-link • Key: abcdefghijk Cisco AP 541N Dual-band Single-radio Access Point Quick Start Guide 162

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
Configuration Examples
Configuring the Wireless Distribution System
Cisco AP 541N Dual-band Single-radio Access Point Quick Start Guide
162
8
Wireless Radio Configuration Using SNMP
STEP 1
Load the Cisco specific MIB module.
STEP 2
From the MIB tree, navigate to the objects in the apRadio table (apRadioBss >
apRadioTable).
STEP 3
Use the apRadioStatus object to set the status of wireless Radio 1 to up (1).
STEP 4
Use the apRadioMode object to set the wireless Radio 1 mode to IEEE 802.11b/g/
n, which is bg-n (4).
STEP 5
Use the apRadioChannelPolicy object to set the channel policy to static (1), which
disables the automatic channel assignment.
STEP 6
Use the apRadioStaticChannel object to set the channel to 6.
STEP 7
Use the apRadioChannelBandwith object to set the channel bandwidth for
wireless Radio 1 to 40-MHz (2).
STEP 8
Use the apRadioTxPower object to set the transmission power on wireless Radio
1 to 75.
STEP 9
Navigate to the objects in the apBssTable.
STEP 10
Use the apBssMaxStations object to set the value of the maximum allowed
stations to 100.
Configuring the Wireless Distribution System
This example shows how to configure a WDS link between two APs. The local
access point is MyAP1 and has a MAC address of 00:1B:E9:16:32:40, and the
remote access point is MyAP2 with a MAC address of 00:30:AB:00:00:B0.
The WDS link has the following settings, which must be configured on both APs:
•
Encryption: WPA (PSK)
•
SSID: wds-link
•
Key: abcdefghijk