Cisco CISCO776 Installation Guide - Page 47

Table 3-1, Verifying the Connections continued, Connection, Normal Pattern, Telephone Devices.

Get Cisco CISCO776 - 776 Router - EN PDF manuals and user guides View all Cisco CISCO776 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 47 highlights

Table 3-1 Verifying the Connections (continued) LED Connection Normal Pattern RDX Ethernet Off when there is no traffic on the network. On when there is traffic is received from the network. TDX Ethernet Off when there is no traffic on the network. On when there is traffic is transmitted to the network. LINK, LK1, LK2, LK3, LK4 Ethernet On when a connection from the Ethernet port to an Ethernet device is established. Blinks while attempting to establish a connection. Off when there is no connection. CH1, CH2 ISDN U or S/T port PH1 and PH21 Analog telephone, fax, or modem On when the router has an active voice or data connection to the WAN or the channel has not yet timed out after the connection was closed. Off when there is no active connection to the WAN and the channel has timed out. On when telephone, fax, or modem is in use. Off when not in use. 1 You can also pick up the handset and listen for a dial tone. Where To Go From Here You have completed the basic hardware installation. You can add digital or analog telephone devices if desired. For additional information, see Chapter 4, "ISDN and Analog Telephone Devices." If your router has been preconfigured by your vendor or a service provider, you should be able to turn on your PC, enter the configuration parameters for the PC (your service provider or network administrator provides these instructions), and connect to the Internet or your corporate network. Once the connection is established, the installation is complete. Installing Your Router 3-11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
Installing Your Router
3-11
Where To Go From Here
You have completed the basic hardware installation. You can add digital or analog
telephone devices if desired. For additional information, see Chapter 4, “ISDN and Analog
Telephone Devices.”
If your router has been preconfigured by your vendor or a service provider, you should be
able to turn on your PC, enter the configuration parameters for the PC (your service
provider or network administrator provides these instructions), and connect to the Internet
or your corporate network. Once the connection is established, the installation is complete.
RDX
Ethernet
Off when there is no traffic on the network.
On when there is traffic is received from the
network.
TDX
Ethernet
Off when there is no traffic on the network.
On when there is traffic is transmitted to the
network.
LINK, LK1,
LK2, LK3,
LK4
Ethernet
On when a connection from the Ethernet port to
an Ethernet device is established.
Blinks while attempting to establish a connection.
Off when there is no connection.
CH1, CH2
ISDN U or S/T port
On when the router has an active voice or data
connection to the WAN or the channel has not yet
timed out after the connection was closed.
Off when there is no active connection to the
WAN and the channel has timed out.
PH1 and PH2
1
Analog telephone, fax,
or modem
On when telephone, fax, or modem is in use.
Off when not in use.
1
You can also pick up the handset and listen for a dial tone.
Table 3-1
Verifying the Connections (continued)
LED
Connection
Normal Pattern