Cisco CISCO776 Installation Guide - Page 59

Disabling the Pound Key’s End-of-Dial Function

Get Cisco CISCO776 - 776 Router - EN PDF manuals and user guides View all Cisco CISCO776 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 59 highlights

Disabling the Pound Key's End-of-Dial Function If the pound (#) key is one of the dialing digits in a telephone number, you can disable the end-of-call function on a per-call basis. This command applies only to INS router software. To disable the end-of-call function, use the following DTMF command: **98# After entering the **98# command, wait for the dial tone and enter the desired dialing digits, including the pound (#) key. The call is sent 6 seconds after the last dialing digit is entered. When the call is terminated, the end-of-call function is restored for the next call. Internal Tones for NET3 and 1TR6 ISDN Lines for Europe Depending on the ISDN service provider, certain internal tones, such as dial, ring back, and busy tones, might not be provided by the telephone switch (the device on the other end of the ISDN line). If this is the case with the ISDN line you are using, you can configure Cisco 700 series routers to provide just the dial tone or all tones. This command applies only to NET3 router software and to 1TR6 router software. The set internaltones command provides just the dial tone or all internal tones. By default, the router provides all internal tones. The following is an example of a set internaltones command that enables the dial tone only: 766> set internaltones dialtone Call Forwarding in Sweden and Finland Call Forwarding supplementary service has been added to software Release 4.0(2) and higher for Sweden and Finland (NET3). The Call Forwarding types supported are as follows: Call Forwarding Unconditional (CFU)-Enables the network to redirect all incoming calls to another party, regardless of the status of the user. Call Forwarding No Reply (CFNR)-Enables the network to redirect calls to another party when the call is not established within a predefined period of time. ISDN and Analog Telephone Devices 4-11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
ISDN and Analog Telephone Devices
4-11
Disabling the Pound Key’s End-of-Dial Function
If the
pound
(#) key is one of the dialing digits in a telephone number, you can disable the
end-of-call function on a per-call basis. This command applies only to INS router software.
To disable the end-of-call function, use the following DTMF command:
**98#
After entering the
**98#
command, wait for the dial tone and enter the desired dialing
digits, including the
pound
(#) key. The call is sent 6 seconds after the last dialing digit is
entered. When the call is terminated, the end-of-call function is restored for the next call.
Internal Tones for NET3 and 1TR6 ISDN Lines for Europe
Depending on the ISDN service provider, certain internal tones, such as dial, ring back, and
busy tones, might not be provided by the telephone switch (the device on the other end of
the ISDN line). If this is the case with the ISDN line you are using, you can configure
Cisco 700 series routers to provide just the dial tone or all tones. This command applies
only to NET3 router software and to 1TR6 router software.
The
set internaltones
command provides just the dial tone or all internal tones. By default,
the router provides all internal tones.
The following is an example of a
set internaltones
command that enables the dial tone
only:
766>
set internaltones dialtone
Call Forwarding in Sweden and Finland
Call Forwarding supplementary service has been added to software Release 4.0(2) and
higher for Sweden and Finland (NET3). The Call Forwarding types supported are as
follows:
Call Forwarding Unconditional (CFU)—Enables the network to redirect all incoming calls
to another party, regardless of the status of the user.
Call Forwarding No Reply (CFNR)—Enables the network to redirect calls to another party
when the call is not established within a predefined period of time.