Cisco SRW2008P User Guide

Cisco SRW2008P - Small Business Managed Switch Manual

Get Cisco SRW2008P - Small Business Managed Switch PDF manuals and user guides
UPC - 745883571024
View all Cisco SRW2008P manuals
Add to My Manuals
Save this manual to your list of manuals

Cisco SRW2008P manual content summary:

  • Cisco SRW2008P | User Guide - Page 1
    USER GUIDE 8-Port 10/100/1000 Managed Gigabit Switch Model: SRW2008/SRW2008P/SRW2008MP BUSINESS SERIES
  • Cisco SRW2008P | User Guide - Page 2
    While reading through the User Guide you may see in front of the address because most current web browsers do not require it. If you use an older web browser, you may have to of Cisco Systems, Inc. and/ or its affiliates in the U.S. and certain other countries. Copyright © 2008 Cisco Systems
  • Cisco SRW2008P | User Guide - Page 3
    the Web-based Utility 17 Setup > Summary 17 Device Information 17 System Information 18 PoE Information 18 Setup > Network Settings 18 Identification 18 IP Configuration 18 Setup > Time 19 Set Time 19 Local Time 19 Daylight Saving 19 8-Port 10/100/1000 Gigabit Switch with Webview ii
  • Cisco SRW2008P | User Guide - Page 4
    21 Port Management > LACP 22 Port Management > PoE Power Settings 22 VLAN Management > Create VLAN 23 Single VLAN 23 VLAN Range 23 VLAN Table 23 VLAN Management > Port Settings 23 VLAN Management > Ports to VLAN 24 VLAN Management > VLAN to Ports 24 Join VLAN Detail 25 VLAN Management
  • Cisco SRW2008P | User Guide - Page 5
    Query 52 Admin > Logging 52 Admin > Port Mirroring 53 Admin > Cable Test 53 Admin > Save Configuration 54 Via TFTP 54 Via HTTP 54 Backup 54 Admin > Firmware Upgrade 54 Admin > Reboot 55 Admin > Factory Defaults 55 Admin > Server Logs 55 8-Port 10/100/1000 Gigabit Switch with Webview iv
  • Cisco SRW2008P | User Guide - Page 6
    Information 71 FCC Statement 71 Safety Notices 71 Industry Canada Statement 71 Avis d' Industrie Canada 71 User Information for Consumer Products Covered by EU Directive 2002/96/EC on Waste Electric and Electronic Equipment (WEEE 72 8-Port 10/100/1000 Gigabit Switch with Webview v
  • Cisco SRW2008P | User Guide - Page 7
    •• SRW2008 8-port 10/100/1000 Ethernet Switch with WebView. Includes 8 10/100/1000 RJ-45 ports and 2 shared MiniGBIC slots. •• SRW2008MP 8-port 10/100/1000 Ethernet Switch with WebView and Maximum POE (Power over Ethernet) Includes 8 10/100/1000 RJ-45 ports and 2 shared MiniGBIC slots. •• SRW2008P
  • Cisco SRW2008P | User Guide - Page 8
    Linksys MGBT1, MGBSX1, or MGBLH1 mini-GBIC modules with the Switch. The MGBSX1 and the MGBLH1 require fiber cabling with LC connectors, while the MGBT1 requires a Category 5e Ethernet cable with an RJ-45 connector. SRW2008P/SRW2008MP - Front Panel The LEDs and ports are located on the front panel
  • Cisco SRW2008P | User Guide - Page 9
    , or MGBLH1 mini-GBIC modules with the Switch. The MGBSX1 and the MGBLH1 require fiber cabling with LC connectors, while the MGBT1 requires a Category 5e Ethernet cable with an RJ-45 connector. Console The Console port is where you can connect a serial cable to a PC's serial port for configuration
  • Cisco SRW2008P | User Guide - Page 10
    not stack free-standing Switches more than four units high. Placement Options There are three ways to physically install the Switch, either set the Switch on its four rubber feet for desktop placement, mount the switch in a standard-sized, 19-inch 8-Port 10/100/1000 Gigabit Switch with Webview 4
  • Cisco SRW2008P | User Guide - Page 11
    damage the Switch and would invalidate your warranty. 3. Make sure the brackets are properly attached to the Switch. 4. Use the appropriate screws (not included) to securely attach the brackets to your rack. Mounting in Rack Attaching the Brackets 8-Port 10/100/1000 Gigabit Switch with Webview 5
  • Cisco SRW2008P | User Guide - Page 12
    Switch. Use the template above to plan your installation. sturdy and make sure the location is within reach of the power and slide the Switch down until the screws fit snugly into the wall Switch. Ensure that the wall you use is smooth, flat, dry and 8-Port 10/100/1000 Gigabit Switch with Webview
  • Cisco SRW2008P | User Guide - Page 13
    Switch. If a port has an active Gigabit connection, then its corresponding Gigabit LED will also light up. NOTE: If you need to reset the Switch, unplug the power cord from the back of the Switch. Wait a few seconds and then reconnect it. 8-Port 10/100/1000 Gigabit Switch with Webview Installation
  • Cisco SRW2008P | User Guide - Page 14
    8-Port 10/100/1000 Gigabit Switch with Webview HyperTerminal Properties Screen Connecting to the Switch through a Telnet Session 1. Open a command line editor and enter telnet 192.168.1.254. Then, press the Enter key. 2. The Login screen will now appear. The first time you open the CLI interface
  • Cisco SRW2008P | User Guide - Page 15
    6. File Management 7. Restore System Default Settings 8. Reboot System 0. Back to Main Menu. System Information From the System Information screen you can check current firmware versions and other general switch information. Main Menu 8-Port 10/100/1000 Gigabit Switch with Webview System
  • Cisco SRW2008P | User Guide - Page 16
    save your changes. To exit, select Quit and press the Enter key. General Information 8-Port 10/100/1000 Gigabit Switch with Webview Serial Port Configuration Telnet Configuration On the Telnet Configuration screen, the time-out is displayed. The value is entered in seconds. If you do not want the
  • Cisco SRW2008P | User Guide - Page 17
    4 Configuration Using the Console Interface Telnet Configuration SSH the RSA and DSA key status, and any open SSH sessions. Select Refresh to update the screen if necessary. To exit, select Quit and press the Enter key. press the Enter key. 8-Port 10/100/1000 Gigabit Switch with Webview 11
  • Cisco SRW2008P | User Guide - Page 18
    state or province name. (Range: 1 - 64) Country Name Specifies the country name. (Range: 2 - 2) Validity Term Specifies number of days certification is valid. (Range: 30 - 3650) User & Password Settings 8-Port 10/100/1000 Gigabit Switch with Webview 12
  • Cisco SRW2008P | User Guide - Page 19
    network's default gateway is displayed. Management VLAN The VLAN ID number is displayed. DHCP client The status of the DHCP client is displayed. If you want the Switch to be a DHCP client, then select ENABLE. If you want to assign an static IP address to the Switch, then enter the IP settings and
  • Cisco SRW2008P | User Guide - Page 20
    Console Interface Ping The Ping screen displays the IP address of the location you want to contact. HTTP HTTPS Configuration Use the HTTPS Configuration screen to configure HTTPS settings. You can enable or disable the HTTPS server and configure the port Port 10/100/1000 Gigabit Switch with Webview
  • Cisco SRW2008P | User Guide - Page 21
    to the factory default settings, select Restore System Default Settings and press the Enter key. You will be asked if you want to continue. Press the y key to restore the Switch's default settings, or press the n key to cancel. Restore Default 8-Port 10/100/1000 Gigabit Switch with Webview Reboot
  • Cisco SRW2008P | User Guide - Page 22
    Chapter 4 Configuration Using the Console Interface The Port Configuration screen displays the port numbers, their status, auto-negotiation status, speed and duplex mode, explains how to navigate the various screens of the console interface. 8-Port 10/100/1000 Gigabit Switch with Webview 16
  • Cisco SRW2008P | User Guide - Page 23
    from the web-based utility: Setup, Port Management, VLAN Management, Statistics, ACL, Security, QoS (Quality of Service), Spanning Tree, Multicast, SNMP, Admin, and Logout. Click one of the main tabs to view additional tabs. Login Screen 8-Port 10/100/1000 Gigabit Switch with Webview NOTE: The LEDs
  • Cisco SRW2008P | User Guide - Page 24
    PoE function is on or off. Mainpower Consumption Displays how much power is currently used. 8-Port 10/100/1000 Gigabit Switch with Webview Setup > Network Settings Setup > Network Settings The Network Settings screen allows you to assign DHCP or static IP settings to interfaces and assign default
  • Cisco SRW2008P | User Guide - Page 25
    of time (in seconds) before the Switch polls the SNTP server. The default value is every 1024 seconds (approx. 17 minutes). Click the Save Settings button to save your changes or click Cancel Changes to discard the information. Port Management > Port Settings The Port Management > Port Settings
  • Cisco SRW2008P | User Guide - Page 26
    VLAN Edge (PVE) port, it bypasses the Forwarding Database and forwards all unicast, multicast, and broadcast traffic to an uplink. Uplinks can be ports or LAGs. Detail The Detail button will open the Port Configuration Detail screen. 8-Port 10/100/1000 Gigabit Switch with Webview Port Management
  • Cisco SRW2008P | User Guide - Page 27
    uplink. Click the Save Settings button to save your changes. 8-Port 10/100/1000 Gigabit Switch with Webview Port Management > Link Aggregation Port Management > Link Aggregation LAG This indicates if the port is part of a LAG. Description Description for this LAG. Admin Status The admin status
  • Cisco SRW2008P | User Guide - Page 28
    Long is the default. Admin Key A channel will only be formed between ports having the same admin key. This only applies to ports located on the same switch. Port Management > PoE Power Settings 8-Port 10/100/1000 Gigabit Switch with Webview Port Management > PoE Power Settings Port Displays the
  • Cisco SRW2008P | User Guide - Page 29
    Port 10/100/1000 Gigabit Switch with Webview VLAN Table The VLAN Table displays a list of all configured VLANs. The VLAN ID, VLAN Name, and status of the VLAN are displayed here. To remove a VLAN, click the Remove button. VLAN Management > Port Settings VLAN Management > Port Settings The VLAN Port
  • Cisco SRW2008P | User Guide - Page 30
    . General Indicates the port belongs to VLANs, and each VLAN is user-defined as tagged or untagged (full 802.1Q mode). 8-Port 10/100/1000 Gigabit Switch with Webview VLAN Management > VLAN to Ports The VLAN to Ports screen contains fields for configuring VLANs to a ports. Interface Displays the
  • Cisco SRW2008P | User Guide - Page 31
    The Update button adds the configured GVRP setting to the table at the bottom of the screen. Statistics > RMON Statistics The RMON Statistics screen contains fields for viewing information about device utilization and errors that occurred on the device. VLAN Management > GVRP The Global System LAG
  • Cisco SRW2008P | User Guide - Page 32
    frames received on the interface since the device was last refreshed. Clear Counters button This option will reset all of the statistic counts. 8-Port 10/100/1000 Gigabit Switch with Webview Refresh Now button Use this option to refresh the statistics. Statistics > RMON History The RMON History
  • Cisco SRW2008P | User Guide - Page 33
    number. Owner Displays the RMON station or user that requested the RMON information. The field range . 8-Port 10/100/1000 Gigabit Switch with Webview CRC Align Errors Displays the number of CRC and contains fields for setting network alarms. Network alarms occur when a network problem, or event,
  • Cisco SRW2008P | User Guide - Page 34
    port. •• LAG Displays the RMON statistics for the selected LAG in the management system. If the device is not reset, the entry time in seconds. 8-Port 10/100/1000 Gigabit Switch with Webview Owner Displays the device or user that defined the alarm. The Add to List button the Event Setting table.
  • Cisco SRW2008P | User Guide - Page 35
    Chapter 5 Advanced Configuration The Add to List button adds the configured RMON event to the Event Table at . 8-Port 10/100/1000 Gigabit Switch with Webview Statistics > 802.1x Statistics Port Indicates the port, which is polled for statistics. Refresh Rate Indicates the amount of time that
  • Cisco SRW2008P | User Guide - Page 36
    Port Indicates port statistics are displayed. •• LAG Indicates LAG statistics are displayed. Refresh Rate Indicates the amount of time 8-Port 10/100/1000 Gigabit Switch with Webview The Clear All Counters button resets all tables. ACL user-defined IP based ACLs. New ACL Name Define a new user-
  • Cisco SRW2008P | User Guide - Page 37
    port to which the packet was addressed. Ports are reactivated from the Port Management Set connection is dropped. Syn Indicates request to start a session. Fin Indicates request to close a session. 8-Port 10/100/1000 Gigabit Switch with Webview Source Port Defines the TCP/UDP source port button
  • Cisco SRW2008P | User Guide - Page 38
    is assigned on a port or LAG, flows from that ingress interface that do not match the ACL are matched to the default rule, which is Drop button adds the ACL Binding configuration to the ACL Binding Table at the bottom of the screen. Security > RADIUS 8-Port 10/100/1000 Gigabit Switch with Webview
  • Cisco SRW2008P | User Guide - Page 39
    the device. TACACS+ provides a centralized user management system, while still retaining consistency with RADIUS and other authentication processes. The TACACS+ protocol ensures network integrity through encrypted 8-Port 10/100/1000 Gigabit Switch with Webview protocol exchanges between the device
  • Cisco SRW2008P | User Guide - Page 40
    Permits immediate port reauthentication. Setting Timer The Setting Timer button opens the Setting Timer screen to configure ports for 802.1x functionality. Setting Timer 802.1x Settings > Setting Timer Port Indicates the port name. 8-Port 10/100/1000 Gigabit Switch with Webview Reauthentication
  • Cisco SRW2008P | User Guide - Page 41
    Gigabit Switch with Webview Trap Frequency The amount of time (in seconds) between traps. The default value is 10 seconds. Security > Multiple Hosts The Multiple Hosts screen allows network managers to configure advanced port-based authentication settings for specific ports and VLANs. Security
  • Cisco SRW2008P | User Guide - Page 42
    Port 10/100/1000 Gigabit Switch with Webview service that classifies flows according to their Layer 2 priority, as set in the VLAN header. QoS refers to Layer 2 traffic and above. QoS handles perflow settings, even within a single traffic class. QoS > CoS Settings QOS > CoS Settings The CoS Settings
  • Cisco SRW2008P | User Guide - Page 43
    queue for which the queue settings are displayed. The possible field range is 1 - 4. WRR Weight Displays the WRR weights to queues. 8-Port 10/100/1000 Gigabit Switch with Webview QoS > Bandwidth The Bandwidth screen allows network managers to define the bandwidth settings for a specified egress
  • Cisco SRW2008P | User Guide - Page 44
    . Committed Burst Size cannot be configured on FE ports. The Add to List button adds the Bandwidth configuration to the Bandwidth Table at the bottom of the screen. QoS > Basic Mode QoS > Basic Mode 8-Port 10/100/1000 Gigabit Switch with Webview The Basic Mode screen contains the following fields
  • Cisco SRW2008P | User Guide - Page 45
    the pull-down menu. The Policy Settings button opens the Policy Name screen. Policy Name Map button opens the New Class Map screen. 8-Port 10/100/1000 Gigabit Switch with Webview manually configured information rates and exceed actions. Aggregate Policer User-defined aggregate policers. 39
  • Cisco SRW2008P | User Guide - Page 46
    Settings The Aggregate Policer button opens the New Aggregate Policer screen. New Aggregate Policer •• Multiple STP Provides full connectivity for packets allocated to any VLAN tree, without creating forwarding loops. 8-Port 10/100/1000 Gigabit Switch with Webview Spanning Tree > STP Status The
  • Cisco SRW2008P | User Guide - Page 47
    are managed when STP is disabled on the port/ device. BPDUs are used to transmit spanning tree information. The possible field values are: 8-Port 10/100/1000 Gigabit Switch with Webview •• Filtering Filters BPDU packets when spanning tree is disabled on an interface. This is the default value
  • Cisco SRW2008P | User Guide - Page 48
    MAC addresses. •• Learning Indicates that the port is in Learning mode. The port cannot forward traffic, however it can learn new MAC addresses. 8-Port 10/100/1000 Gigabit Switch with Webview •• Forwarding Indicates that the port is in Forwarding mode. The port can forward traffic and learn new
  • Cisco SRW2008P | User Guide - Page 49
    Protocols (NCP) packets to select and configure one or more network layer protocols. When each of the chosen network 8-Port 10/100/1000 Gigabit Switch with Webview layer protocols has been configured, packets from each network layer protocol can be sent over the link. The link remains configured
  • Cisco SRW2008P | User Guide - Page 50
    port provides connectivity from a MSTP region to the outlying CIST root. •• Internal Indicates the port is an internal port. Role Indicates the port role assigned by the STP algorithm in order to provide to STP paths.The possible field values are: 8-Port 10/100/1000 Gigabit Switch with Webview
  • Cisco SRW2008P | User Guide - Page 51
    of time host waits to receive a message before timing out. The default time is 260 seconds. MRouter Timeout Indicates the amount of the time the Multicast router waits to receive a message before it times out. The default value is 300 seconds. 8-Port 10/100/1000 Gigabit Switch with Webview 45
  • Cisco SRW2008P | User Guide - Page 52
    IP Multicast DIsplays the port that can be added to a Multicast service. LAG Displays LAG that can be added to a Multicast service. The configuration options are as follows: •• Static Indicates the port is user-defined. 8-Port 10/100/1000 Gigabit Switch with Webview Multicast > Multicast Forward
  • Cisco SRW2008P | User Guide - Page 53
    user-defined views. The options are as follows: •• Default Displays the default SNMP view for read and read/write views. •• DefaultSuper Displays the default List button adds the Views configuration to the Views Table at the bottom of the screen. 8-Port 10/100/1000 Gigabit Switch with Webview 47
  • Cisco SRW2008P | User Guide - Page 54
    , and changes cannot be made to the assigned SNMP view. •• Write The management access is read-write and changes can be made to the assigned SNMP view. 8-Port 10/100/1000 Gigabit Switch with Webview SNMP > Group Membership The Group Membership screen provides information for assigning SNMP access
  • Cisco SRW2008P | User Guide - Page 55
    Name Contains a list of user-defined SNMP views. Advanced Enables management station IP address. •• All Includes all management station IP addresses. Community String Defines the password used to authenticate the management station to the device. 8-Port 10/100/1000 Gigabit Switch with Webview
  • Cisco SRW2008P | User Guide - Page 56
    password used to authenticate the management station 8-Port 10/100/1000 Gigabit Switch with Webview The Add to List button adds users, and the trap type sent. SNMP notification filters provide the following services: •• Identifying Management at any one time, but not both at the same time. If SNMPv1
  • Cisco SRW2008P | User Guide - Page 57
    password for authentication. •• RADIUS Authenticates the user at the RADIUS server. •• TACACS+ Authenticates the user at the TACACS+ server. •• None Assigns no authentication method to the authentication profile. User Name Displays the user name. 8-Port 10/100/1000 Gigabit Switch with Webview
  • Cisco SRW2008P | User Guide - Page 58
    Dynamic MAC Address Table, including the interface type, MAC addresses, VLAN, and table storing. The Dynamic MAC Address table contains information about the aging time before a dynamic MAC 8-Port 10/100/1000 Gigabit Switch with Webview Admin > Logging Event messages have a unique format, as per
  • Cisco SRW2008P | User Guide - Page 59
    . Network administrators configure port mirroring by selecting a specific port to copy all packets, and different ports from which the packets are copied. 8-Port 10/100/1000 Gigabit Switch with Webview Admin > Cable Test Port This is the port to which the cable is connected. Test Result This
  • Cisco SRW2008P | User Guide - Page 60
    code, refrain from reseting the device. 2. Download the new software image. 3. Reset the device now. Upgrade Select this option to upgrade the switch from a file file. The default is StartupCfg.cfg. 8-Port 10/100/1000 Gigabit Switch with Webview Admin > FIrmware Upgrade The Firmware Upgrade screen
  • Cisco SRW2008P | User Guide - Page 61
    Admin > Factory Defaults The Factory Reset screen allows network managers to reset the device to the factory defaults shipped with the switch. Restoring factory defaults results in erasing the configuration file. Admin > Factory Defaults 8-Port 10/100/1000 Gigabit Switch with Webview Admin > Server
  • Cisco SRW2008P | User Guide - Page 62
    Flash Log screen contains information about log entries saved to the Log File in FLASH, including the time the log was generated, the log severity, and a description of the log message. The Message Log is available after reboot. Admin > Flash Logs 8-Port 10/100/1000 Gigabit Switch with Webview 56
  • Cisco SRW2008P | User Guide - Page 63
    a connector that fits into a fiber port on a network adapter, hub, or switch. In the USA, most cables use a square SC connector that slides and locks into place when plugged into a port or connected to another cable. In Europe, the round ST connector is more prevalent. For Gigabit Ethernet, you must
  • Cisco SRW2008P | User Guide - Page 64
    locate the file for download within a certain time, the device will reset. 7. Select Send File from the Transfer pull-down menu. Auto-Boot Messages 5. When the auto-boot message appears, press the Enter key to access the Startup menu. 8-Port 10/100/1000 Gigabit Switch with Webview Send File 8. In
  • Cisco SRW2008P | User Guide - Page 65
    Appendix B 9. Press Send and the software is downloaded. Download After the software has been downloaded, the device will reboot automatically. Downloading Using Xmodem 8-Port 10/100/1000 Gigabit Switch with Webview 59
  • Cisco SRW2008P | User Guide - Page 66
    given device or network. Bandwidth Assignments Indicates the amount of bandwidth assigned to a specific application, user, and/or interface. 8-Port 10/100/1000 Gigabit Switch with Webview Baud Indicates the number of signaling elements transmitted each second. Best Effort Indicates that traffic
  • Cisco SRW2008P | User Guide - Page 67
    IP layer. ISP (Internet Service Provider) A company that provides access to the Internet. Jumbo Frames Enable transporting identical data in fewer frames. Jumbo Frames reduce overhead, lower processing time, and ensure fewer interrupts. LAG (Link Aggregated Group) Aggregates ports or VLANs into
  • Cisco SRW2008P | User Guide - Page 68
    power. QoS (Quality of Service) Provides policies that contain sets of filters (rules). QoS allows network managers to decide how and what network traffic is forwarded according to priorities, application types, and source and destination addresses. 8-Port 10/100/1000 Gigabit Switch with Webview
  • Cisco SRW2008P | User Guide - Page 69
    set of instructions PCs use to communicate over a network. Telnet A user command and TCP/IP protocol used for accessing remote PCs. TFTP (Trivial File Transfer Protocol) A version of the TCP/IP FTP protocol that has no directory or password Port 10/100/1000 Gigabit Switch with Webview Glossary 63
  • Cisco SRW2008P | User Guide - Page 70
    Forwarding Rate Layer 2 MAC table size Number of VLANs VLAN HOL Blocking Management Web User Interface SNMP SNMP MIBs SRW2008 8 RJ-45 Connectors for 10BASE-T/100BASE-TX/ 1000Base-T with 2 shared SFP ports on port 7 and 8 (combo port) Console Port Auto MDI/MDI-X Autonegotiate/Manual Setting UTP
  • Cisco SRW2008P | User Guide - Page 71
    ad LACP, 802.1d STP, 802.1Q/p VLAN, 802.1w Rapid STP, 802.1s Multiple STP, 802.1x Port Access Authentication 279,4 x 44,45 x 170 mm 1 kg External AC Power Adapter FCC Part15 Class A, CE Class A, UL, cUL, CE Mark, CB 0 to 40ºC -20 to 70ºC 8-Port 10/100/1000 Gigabit Switch with Webview Operating
  • Cisco SRW2008P | User Guide - Page 72
    , RFC 2618 RADIUS Client MIB, RFC 1215 Traps Private POE MIB Embedded Remote Monitoring (RMON) Software Agent Supports four RMON Groups 8-Port 10/100/1000 Gigabit Switch with Webview Firmware Upgrade Port Mirroring Other Management Security Features IEEE 802.1X Access Control Availability Link
  • Cisco SRW2008P | User Guide - Page 73
    to change without notice. 8-Port 10/100/1000 Gigabit Switch with Webview Model Ports Cabling Type LEDs POE Performance Switching Capacity Forwarding Rate Layer 2 MAC table size Number of VLANs VLAN HOL Blocking Management Web User Interface SNMP SNMP MIBs RMON SRW2008P 8 RJ-45 Connectors for
  • Cisco SRW2008P | User Guide - Page 74
    100BASE-TX Fast Ethernet, 802.3ab 1000BASE-T Gigabit Ethernet 802.3z Gigabit Ethernet 802.3x Flow Control, 802.3 ad LACP, 802.3af PoE 802.1d STP, 802.1Q/p VLAN, 802.1w Rapid STP, 802.1s Multiple STP, 802.1x Port Access Authentication 279,4 x 44,45 x 170 mm 1,2 kg External AC Power Adapter FCC
  • Cisco SRW2008P | User Guide - Page 75
    instructions on how to obtain warranty service. The telephone number for Linksys Technical Support in your area can be found in the product User Guide and at www.linksys.com. Have your product serial number and proof of purchase on hand when calling. A DATED PROOF OF ORIGINAL PURCHASE IS REQUIRED
  • Cisco SRW2008P | User Guide - Page 76
    be found at: www.linksys.com/support. This limited warranty is governed by the laws of the jurisdiction in which the Product was purchased by you. Please direct all inquiries to: Linksys, P.O. Box 18558, Irvine, CA 92623. Warranty Information 8-Port 10/100/1000 Gigabit Switch with Webview 70
  • Cisco SRW2008P | User Guide - Page 77
    instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required Cet appareil numérique de la classe A est conforme à la norme NMB-003 d' Industrie Canada
  • Cisco SRW2008P | User Guide - Page 78
    EU Directive 2002/96/EC on Waste Electric and Electronic Equipment (WEEE) This document contains important information for users with regards to the proper disposal and recycling of Linksys products. Consumers are required contact your local authorities, waste disposal service, or the shop where you
  • Cisco SRW2008P | User Guide - Page 79
    contre l'impact néfaste potentiel de ce type de produits sur l'environnement et la santé publique. Pour plus d'informations sur le mode d'élimination de votre équipement, veuillez prendre contact avec les pouvoirs publics locaux, le service de traitement des déchets, ou l'endroit où vous avez acheté
  • Cisco SRW2008P | User Guide - Page 80
    de plaatselijke autoriteiten of afvalverwerkingsdienst, of met de winkel waar u het product hebt aangeschaft. Norsk (Norwegian) - Miljøinformasjon for kunder i EU EU-direktiv 2002/96/EF krever at utstyr med følgende symbol avbildet på produktet og/eller pakningen, ikke må kastes sammen med usortert
  • Cisco SRW2008P | User Guide - Page 81
    de autorităţile locale. Casarea şi reciclarea corecte vor ajuta la prevenirea potenţialelor consecinţe negative asupra sănătăţii mediului şi kupili. Suomi (Finnish) - Ympäristöä koskevia tietoja EUalueen asiakkaille EU-direktiivi 2002/96/EY edellyttää, että jos laitteistossa on tämä symboli itse
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
USER GUIDE
BUSINESS SERIES
8-Port 10/100/1000
Managed Gigabit Switch
Model:
SRW2008/SRW2008P/SRW2008MP