Home » Cisco Manuals » Hubs & Switches » Cisco SRW2008P » Manual Viewer

Cisco SRW2008P User Guide - Page 38

ACL Name, New ACL Name, Delete ACL, Action, Permit, Shutdown, Source MAC Address, Wildcard Mask,

UPC - 745883571024

View all Cisco SRW2008P manuals

Add to My Manuals
Save this manual to your list of manuals

Page 38 highlights

Chapter 5 Advanced Configuration The MAC Based ACL screen allows a MAC based ACL to be defined. ACEs can be added only if the ACL is not bound to an interface. ACL Name Displays the user-defined MAC based ACLs. New ACL Name Specifies a new user-defined MAC based ACL name. Delete ACL Deletes the selected ACL. Action Indicates the ACL forwarding action. Possible field values are: •• Permit Forwards packets which meet the ACL criteria. •• Deny Drops packets which meet the ACL criteria. •• Shutdown Drops packet that meet the ACL criteria, and disables the port to which the packet was addressed. Source MAC Address Matches the source MAC address to which packets are addressed to the ACE. Wildcard Mask Defines the source IP address wildcard mask. Wildcard masks specify which bits are used and which bits are ignored. A wild card mask of 255.255.255.255 indicates that no bit is important. A wildcard of 0.0.0.0 indicates that all the bits are important. For example, if the source IP address 149.36.184.198 and the wildcard mask is 255.36.184.00, the first eight bits of the IP address are ignored, while the last eight bits are used. Dest. MAC Address Matches the destination MAC address to which packets are addressed to the ACE. Wildcard Mask Defines the destination IP address wildcard mask. VLAN ID Matches the packet's VLAN ID to the ACE. The possible field values are 2 to 4094. Ether Type Specifies the packet's Ethernet type. The Add to List button adds the configured MAC Based ACLs to the MAC Based ACL Table at the bottom of the screen. Security > ACL Binding Security > ACL Binding When an ACL is bound to an interface, all the ACE rules that have been defined are applied to the selected interface. Whenever an ACL is assigned on a port or LAG, flows from that ingress interface that do not match the ACL are matched to the default rule, which is Drop unmatched packets. Interface Indicates the interface to which the ACL is bound. ACL Name Indicates the ACL which is bound to the interface. The Add to List button adds the ACL Binding configuration to the ACL Binding Table at the bottom of the screen. Security > RADIUS 8-Port 10/100/1000 Gigabit Switch with Webview Security > RADIUS 32

Section	Page
Chapter 1: Introduction	7
Welcome	7
Chapter 2: Product Overview	8
SRW2008 - Front Panel	8
LEDs	8
Ports	8
SRW2008P/SRW2008MP - Front Panel	8
LEDs	8
Ports	8
Back Panel	9
Chapter 3: Installation	10
Overview	10
Positioning the Switch	10
Placement Options	10
Desktop Placement	10
Rack-Mount Placement	11
Wall-Mount Placement	12
Chapter 4: Configuration Using the Console Interface	14
Overview	14
Configuring the HyperTerminal Application	14
Connecting to the Switch through a Telnet Session	14
Configuring the Switch through the Console Interface	15
Switch Main Menu	15
System Configuration Menu	15
Port Status	21
Port Configuration	21
Chapter 5: Advanced Configuration	23
Overview	23
Accessing the Web-based Utility	23
Setup > Summary	23
Device Information	23
System Information	24
PoE Information	24
Setup > Network Settings	24
Identification	24
IP Configuration	24
Setup > Time	25
Set Time	25
Local Time	25
Daylight Saving	25
SNTP Servers	25
Port Management > Port Settings	25
Port Configuration Detail	26
Port Management > Link Aggregation	27
Link Aggregation Detail	27
Port Management > LACP	28
Port Management > PoE Power Settings	28
VLAN Management > Create VLAN	29
Single VLAN	29
VLAN Range	29
VLAN Table	29
VLAN Management > Port Settings	29
VLAN Management > Ports to VLAN	30
VLAN Management > VLAN to Ports	30
Join VLAN Detail	31
VLAN Management > GVRP	31
Statistics > RMON Statistics	31
Statistics > RMON History	32
Log Table	32
RMON History	33
Statistics > RMON Alarms	33
Statistics > RMON Events	34
Add Event	34
Statistics > Port Utilization	35
Statistics > 802.1x Statistics	35
Statistics > GVRP Statistics	36
ACL > IP based ACL	36
ACL > MAC based ACL	37
Security > ACL Binding	38
Security > RADIUS	38
Security > TACACS+	39
Security > 802.1x Settings	40
Setting Timer	40
Security > Ports Security	40
Security > Multiple Hosts	41
Security > Storm Control	42
QoS	42
QoS > CoS Settings	42
CoS Default	43
QoS > Queue Settings	43
QoS > DSCP Settings	43
QoS > Bandwidth	43
QoS > Basic Mode	44
QoS > Advanced Mode	44
Out of Profile DSCP	45
Policy Name	45
New Class Map	45
New Aggregate Policer	46
Spanning Tree	46
Spanning Tree > STP Status	46
Spanning Tree > Global STP	47
Global Setting	47
Bridge Settings	47
Spanning Tree > STP Port Settings	48
Spanning Tree > RSTP Port Settings	48
Spanning Tree > MSTP Properties	49
Spanning Tree > MSTP Instance Settings	50
Spanning Tree > MSTP Interface Settings	50
Multicast > IGMP Snooping	51
Multicast > Bridge Multicast	52
Multicast > Bridge Multicast Forward All	52
SNMP > Global Parameters	52
SNMP > Views	53
SNMP > Group Profile	54
SNMP > Group Membership	54
SNMP > Communities	55
Base Table	55
Advanced Table	56
SNMP > Notification Filter	56
SNMP > Notification Recipient	56
Admin > User Authentication	57
Admin > Static Address	57
Query	58
Admin > Dynamic Address	58
Query	58
Admin > Logging	58
Admin > Port Mirroring	59
Admin > Cable Test	59
Admin > Save Configuration	60
Via TFTP	60
Via HTTP	60
Backup	60
Admin > Firmware Upgrade	60
Admin > Reboot	61
Admin > Factory Defaults	61
Admin > Server Logs	61
Admin > Memory Logs	62
Admin > Flash Logs	62
Appendix A: About Gigabit Ethernet and Fiber Optic Cabling	63
Gigabit Ethernet	63
Fiber Optic Cabling	63
Appendix B: Introduction	64
Startup Menu Procedures	64
Appendix C: Glossary	66
Appendix D: Specifications	70
Appendix E: Warranty Information	75
Exclusions and Limitations	75
Obtaining Warranty Service	75
Technical Support	76
Appendix E: Regulatory Information	77
FCC Statement	77
Safety Notices	77
Industry Canada Statement	77
Avis d’ Industrie Canada	77

Match case Limit results 1 per page

Chapter 5

Advanced Configuration

8-Port 10/100/1000 Gigabit Switch with Webview

The

MAC Based ACL

screen allows a MAC based ACL to be

defined. ACEs can be added only if the ACL is not bound

to an interface.

ACL Name

Displays the user-defined MAC based ACLs.

New ACL Name

Specifies a new user-defined MAC based

ACL name.

Delete ACL

Deletes the selected ACL.

Action

Indicates the ACL forwarding action. Possible field

values are:

Permit

•

Forwards

packets

which

meet

the

ACL

criteria.

Deny

•

Drops packets which meet the ACL criteria.

Shutdown

•

Drops packet that meet the ACL criteria,

and disables the port to which the packet was

addressed.

Source MAC Address

Matches the source MAC address

to which packets are addressed to the ACE.

Wildcard Mask

Defines the source IP address wildcard

mask. Wildcard masks specify which bits are used and

which bits are ignored. A wild card mask of 255.255.255.255

indicates that no bit is important. A wildcard of 0.0.0.0

indicates that all the bits are important. For example, if the

source IP address 149.36.184.198 and the wildcard mask

is 255.36.184.00, the first eight bits of the IP address are

ignored, while the last eight bits are used.

Dest.

MAC

Address

Matches

the

destination

MAC

address to which packets are addressed to the ACE.

Wildcard

Mask

Defines

the

destination

address

wildcard mask.

VLAN ID

Matches the packet’s VLAN ID to the ACE. The

possible field values are 2 to 4094.

Ether Type

Specifies the packet’s Ethernet type.

The

Add to List

button adds the configured MAC Based

ACLs to the MAC Based ACL Table at the bottom of the

screen.

Security > ACL Binding

When an ACL is bound to an interface, all the ACE rules that

have been defined are applied to the selected interface.

Whenever an ACL is assigned on a port or LAG, flows

from that ingress interface that do not match the ACL are

matched to the default rule, which is Drop unmatched

packets.

Interface

Indicates the interface to which the ACL is

bound.

ACL Name

Indicates the ACL which is bound to the

interface.

The

Add to List

button adds the ACL Binding configuration

to the ACL Binding Table at the bottom of the screen.

Security > RADIUS