Dell Latitude E6400 XFR Service Manual - Page 63

DC Power Cable, Base Assembly

Get Dell Latitude E6400 XFR PDF manuals and user guides View all Dell Latitude E6400 XFR manuals
Add to My Manuals
Save this manual to your list of manuals

Page 63 highlights

Dell™ Latitude™ E6400 XFR Service Manual 3 M2.5 x 5-mm screw 4 Modem connector 33 DC Power Cable 33.1 Removing the DC Power Cable CAUTION: Before you begin any of the procedures in this section, follow the safety instructions that shipped with your computer. 1. Follow the instructions in Before Working on Your Computer. 2. Remove the system board (see Removing the System Board Assembly). NOTE: Do not remove the mini-pci wireless or FCM cards, memory modules, or processor from the system board. 3. Unroute the DC power cable from the base assembly. Pry up the DC power connector to release the double- stick adhesive tape on the bottom of the connector, and then lift the DC power connector out of the base assembly. 1 2 1 DC power connector 2 DC cable 33.2 Replacing the DC Power Cable CAUTION: Before you begin any of the procedures in this section, follow the safety instructions that shipped with your computer. 1. Place the DC power cable in the base assembly, aligning the guides on the connector sides with the base. Once installed, press down firmly on top of the DC power connector to seal the adhesive to the base. 2. Route the DC power cable in the base assembly. 3. Replace the system board (see Replacing the System Board Assembly). 4. Follow the procedures in After Working on Your Computer. 34 Base Assembly 34.1 Removing the Base Assembly 1. Follow the procedures in Before Working on Your Computer. 2. Remove the system board (see Removing the System Board Assembly). NOTE: Do not remove the mini-pci wireless or FCM cards, memory modules, or processor from the system board. 3. Remove the SIM card assembly (see Removing the SIM Card Assembly). 4. Remove the modem (see Removing the Modem). 34.2 Replacing the Base Assembly Page 63

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
Dell
™
Latitude™ E6400 XFR Service Manual
Page 63
3
M2.5 x 5-mm screw
4
Modem connector
33
DC Power Cable
33.1
Removing the DC Power Cable
CAUTION:
Before you begin any of the procedures in this section, follow the safety
instructions that shipped with your computer.
1.
Follow the instructions in Before Working on Your Computer
.
2.
Remove the system board (see Removing the System Board Assembly
).
NOTE:
Do not remove the mini-pci wireless or FCM cards, memory modules, or processor from
the system board.
3.
Unroute the DC power cable from the base assembly.
Pry up the DC power connector to release the double-
stick adhesive tape on the bottom of the connector, and then lift the DC power connector out of the base
assembly.
1
DC power connector
2
DC cable
33.2
Replacing the DC Power Cable
CAUTION:
Before you begin any of the procedures in this section, follow the safety
instructions that shipped with your computer.
1.
Place the DC power cable in the base assembly, aligning the guides on the connector sides with the base.
Once installed, press down firmly on top of the DC power connector to seal the adhesive to the base.
2.
Route the DC power cable in the base assembly.
3.
Replace the system board (see Replacing the System Board Assembly
).
4.
Follow the procedures in After Working on Your Computer
.
34
Base Assembly
34.1
Removing the Base Assembly
1.
Follow the procedures in Before Working on Your Computer
.
2.
Remove the system board (see Removing the System Board Assembly
).
NOTE:
Do not remove the mini-pci wireless or FCM cards, memory modules, or processor from
the system board.
3.
Remove the SIM card assembly (see Removing the SIM Card Assembly
).
4.
Remove the modem (see Removing the Modem
).
34.2
Replacing the Base Assembly
1
2