Dell PowerConnect FCS624S Web Management Interface User Guide - Page 63

Configuring stack ports, Con gt; Stack > Stack-Ports, Modify, Apply

Get Dell PowerConnect FCS624S PDF manuals and user guides View all Dell PowerConnect FCS624S manuals
Add to My Manuals
Save this manual to your list of manuals

Page 63 highlights

Configuring stack ports 4 The Configure Unit Priority window contains the following information. Unit ID Priority The stack identification number for this unit. A number from 0 to 255 (255 is the highest priority). Additional information you can configure or view includes: • Show priority • Add module (refer to page 56) Configuring stack ports Select Configure > Stack > Stack-Ports to configure a stack. Click Modify to modify the configuration of a port. Click Apply to save your configuration. FIGURE 35 Configuring stack ports NOTE When you assign an unused ID to a new stack unit, once this unit is reset, it assumes the new ID. All configuration information related to the previous unit that used the ID is deleted. The Active Controller learns the configuration for the new unit (instead of creating an interface configuration for the new unit). If the configuration for a unit being replaced does not match the new unit type, the Active Controller removes the unit configuration and associated interface configuration. You can also view details of Show Stack Details, Show Stack Modules, and Add Module. For more information on adding a module, refer to page 56. PowerConnect B-Series FCX Web Management Interface User Guide 53 53-1002268-01

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
PowerConnect B-Series FCX Web Management Interface User Guide
53
53-1002268-01
Configuring stack ports
4
The Configure Unit Priority window contains the following information.
Additional information you can configure or view includes:
•
Show priority
•
Add module (refer to
page 56
)
Configuring stack ports
Select
Configure > Stack > Stack-Ports
to configure a stack. Click
Modify
to modify the
configuration of a port. Click
Apply
to save your configuration.
FIGURE 35
Configuring stack ports
NOTE
When you assign an unused ID to a new stack unit, once this unit is reset, it assumes the new ID. All
configuration information related to the previous unit that used the ID is deleted. The Active
Controller learns the configuration for the new unit (instead of creating an interface configuration for
the new unit).
If the configuration for a unit being replaced does not match the new unit type, the Active Controller
removes the unit configuration and associated interface configuration.
You can also view details of Show Stack Details, Show Stack Modules, and Add Module. For more
information on adding a module, refer to
page 56
.
Unit ID
The stack identification number for this unit.
Priority
A number from 0 to 255 (255 is the highest priority).