Epson Endeavor User Setup Information - Page 28

Starting The Setup Program, Floppy Disk Type Is Set Incorrectly Or, Drive Error

Get Epson Endeavor PDF manuals and user guides View all Epson Endeavor manuals
Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

The configuration you define through SETUP is stored in a special area of memory called CMOS RAM. This memory is backed up by a battery, so it is not erased when you turn off or reset the computer. Whenever you reboot the computer, it checks the settings, and if it discovers a difference between the information in the CMOS RAM and its actual hardware configuration, it prompts you to run SETUP. You see a message such as the following: FLOPPY DISK TYPE IS SET INCORRECTLY OR DRIVE ERROR You also see the following prompt at the bottom of the screen: Press F1 to continue or Del to start SETUP If this happens, press IDelete) to run SETUP and correct the setting. Starting the SETUP Program To start SETUP, make sure there is no diskette in the diskette drive; then turn on your computer. (If your computer is already on, turn it off, wait 20 seconds, and then turn it on again.) After the self test, you see the following prompt at the bottom of the screen: Press Del to start SETUP As soon as you see this message, press [c). If you do not press [a) within approximately five seconds, the computer starts loading the operating system and you will not be able to run SETUP. If this happens, restart the computer and try again. When you press [El, you'll see the first SETUP screen. 2-2 Running the SETUP Program

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
The configuration you define through SETUP is stored in a
special area of memory called CMOS RAM. This memory is
backed up by a battery, so it is not erased when you turn off or
reset the computer. Whenever you reboot the computer, it
checks the settings, and if it discovers a difference between the
information in the CMOS RAM and its actual hardware
configuration, it prompts you to run SETUP. You see a message
such as the following:
FLOPPY DISK TYPE IS SET INCORRECTLY OR
DRIVE ERROR
You also see the following prompt at the bottom of the screen:
Press F1 to continue or Del to start SETUP
If this happens, press
IDelete)
to run SETUP and correct the
setting.
Starting the SETUP Program
To start SETUP, make sure there is no diskette in the diskette
drive; then turn on your computer. (If your computer is already
on, turn it off, wait 20 seconds, and then turn it on again.) After
the self test, you see the following prompt at the bottom of the
screen:
Press Del to start SETUP
As soon as you see this message, press
[c).
If you do not press
[a)
within approximately five seconds,
the computer starts loading the operating system and you will
not be able to run SETUP. If this happens, restart the computer
and try again.
When you press
[El,
you’ll see the first SETUP screen.
2-2
Running the SETUP
Program