Epson MX-80II User Manual - Page 23

INSTALLATION OF MX-80 F/T TYPE II, Unpacking, Unpacking steps, Counting the Parts

Get Epson MX-80II PDF manuals and user guides View all Epson MX-80II manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

INSTALLATION OF MX-80 F/T TYPE II 1. Unpacking Before removing the MX-80 F/T Type II from the carton, check the box for evidence of shipping damage or mishandling. If such evidence is present, notify the carrier immediately. 1.1. Unpacking steps Unpacking steps are as follows: STEP 1. Open the carton. STEP 2. Remove accessories. STEP 3. Remove the MX-80 F/T Type I I by holding its underside and lifting it straight up with the packing material attached. STEP 4. Place the Printer with the packing material on a table or any other convenient flat surface. STEP 5. Take off the packing material carefully. STEP 6. Remove the vinyl cover. 1.2. Repacking steps Repacking can be carried out by following the above steps in the reverse order. (Repacking: Shipment for repair, storage, etc.) NOTE: It is recommended that all original packing materials be saved for reuse in case the MX-80 F/T Type I I requires reshipment in the future. 2. Counting the Parts The MX-80 F/T Type I I and standard accessories are as shown in Fig. 19. Upon unpacking, if you notice any listed contents missing or evident damage, contact the store where you purchased the MX-80 F/T Type I I as soon as possible. -17-

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
INSTALLATION OF MX-80 F/T TYPE II
1. Unpacking
Before removing the MX-80 F/T Type II from the carton, check the box for
evidence of shipping damage or mishandling. If such evidence is present, notify the
carrier immediately.
1.1. Unpacking steps
Unpacking steps are as follows:
STEP 1.
Open the carton.
STEP 2. Remove accessories.
STEP 3.
Remove the MX-80 F/T Type I I by holding its underside and lifting it
straight up with the packing material attached.
STEP 4. Place the Printer with the packing material on a table or any other
convenient flat surface.
STEP 5.
Take off the packing material carefully.
STEP 6.
Remove the vinyl cover.
1.2. Repacking steps
Repacking can be carried out by following the above steps in the reverse order.
(Repacking: Shipment for repair, storage, etc.)
NOTE: It is recommended that all original packing materials be saved for reuse in case the
MX-80 F/T Type I I requires reshipment in the future.
2. Counting the Parts
The MX-80 F/T Type I I and standard accessories are as shown in Fig. 19. Upon
unpacking, if you notice any listed contents missing or evident damage, contact the
store where you purchased the MX-80 F/T Type I I as soon as possible.
-17-