Fluke 1586A/2HC Product Manual - Page 126

Reinstall the Input Module that was used when

Get Fluke 1586A/2HC PDF manuals and user guides View all Fluke 1586A/2HC manuals
Add to My Manuals
Save this manual to your list of manuals

Page 126 highlights

1586A Users Manual Error Code Error 422 Error 423 Error 424 Error 425 Error 427 Error 428 Error 429 Error 430 Table 7-1. Error Messages (cont.) Error Message Causes and Solutions Not a totalizer channel Cause: Error occurs when a user attempts to set a TOT channel on any channel other than Ch402. Solution: Check the parameter value and try again. Not an analog channel Cause: Error occurs when a user attempts to set an analog channel on any channel other than Chx01 through Chx22. Solution: Check the parameter value and try again 3-wire or 4-wire not allowed on channel Cause: Channel cannot be configured for 3-wire or 4-wire because (1.) the input type does not support it (2.) the channel is not a dedicated sense channel. Solution: Check to make sure that the sense wires are in the sense terminals and not the input terminals. When a sense is configured, it is configured on the channel associated with the input terminal and automatically reserves the sense channel directly across from the input. See Chapter 2 and Chapter 3 for more information. Function not allowed on current channel Cause: Chx21 or Chx22 can only be configured as a current channel. Solution: Set up the input on a different channel. Invalid current channel Cause: An Input Module was swapped with an external Input Module while a scan was paused. Solution: Reinstall the Input Module that was used when the scan was started. Parameter value out Cause: Parameter in command exceeds the limit. of range Solution: Check the parameter value and try again. Channel limit exceeded Cause: A single math channel is configured to use more than 10 channels. Solution: Limit the number of math channels to no more than 10 with the CALCulate:MATH:SOURce command. String too long Cause: Too many characters are included in a string parameter. For example,Probe ID (max. 24 characters); Unit (max. 3 characters); Channel label (max. 16 characters); Test setup file name (max. 8 characters). Solution: Check the parameter value and try again. 7-12 MyFlukeStore Shop for Fluke products online at: www. .com 1.888.610.7664

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
1586A
Users Manual
7-12
Table 7-1. Error Messages (cont.)
Error Code
Error Message
Causes and Solutions
Error 422
Not a totalizer
channel
Cause:
Error occurs when a user attempts to set a TOT
channel on any channel other than Ch402.
Solution:
Check the parameter value and try again.
Error 423
Not an analog
channel
Cause:
Error occurs when a user attempts to set an analog
channel on any channel other than Chx01 through Chx22.
Solution:
Check the parameter value and try again
Error 424
3-wire or 4-wire not
allowed on channel
Cause:
Channel cannot be configured for 3-wire or 4-wire
because (1.) the input type does not support it (2.) the
channel is not a dedicated sense channel.
Solution:
Check to make sure that the sense wires are in the
sense terminals and not the input terminals. When a sense is
configured, it is configured on the channel associated with the
input terminal and automatically reserves the sense channel
directly across from the input. See Chapter 2 and Chapter 3
for more information.
Error 425
Function not allowed
on current channel
Cause:
Chx21 or Chx22 can only be configured as a current
channel.
Solution:
Set up the input on a different channel.
Error 427
Invalid current
channel
Cause:
An Input Module was swapped with an external Input
Module while a scan was paused.
Solution:
Reinstall the Input Module that was used when the
scan was started.
Error 428
Parameter value out
of range
Cause:
Parameter in command exceeds the limit.
Solution:
Check the parameter value and try again.
Error 429
Channel limit
exceeded
Cause:
A single math channel is configured to use more than
10 channels.
Solution:
Limit the number of math channels to no more than
10 with the CALCulate:MATH:SOURce command.
Error 430
String too long
Cause:
Too many characters are included in a string
parameter. For example,Probe ID (max. 24 characters); Unit
(max. 3 characters); Channel label (max. 16 characters); Test
setup file name (max. 8 characters).
Solution:
Check the parameter value and try again.
Shop for Fluke products online at:
1.888.610.7664
www.
MyFlukeStore
.com