Home » Fujitsu Manuals » Scanners » Fujitsu 6240 » Manual Viewer

Fujitsu 6240 Operating Guide - Page 133

Before Using This Function

UPC - 097564307270

Add to My Manuals
Save this manual to your list of manuals

Page 133 highlights

3.18 Not Detecting Multifeed for Fixed Format q Intelligent Multifeed Function Select one of three modes described above. q Clear overlap pattern If this checkbox is marked, the remembered length and location of glued paper (overlap pattern) are deleted from memory. The overlap pattern is also deleted from memory if you change the Intelligent Multifeed Function mode. Before Using This Function Configure the following settings before using this function: 1. When the TWAIN driver is used; select [Use Memory on Scanner] or [Use both Memory] as [Cache Mode] on the [Job/Cache] tab of the [Option] dialog box. Without this step, you cannot continue scanning after a multifeed error. 2. When the ISIS or the TWAIN driver is used; if you want to start scanning by using the [Scan] button after a multifeed error, configure the driver settings as described below. [TWAIN driver] Mark the [Enable Scanner Panel] and [Enable [Scan] Button] checkboxes on the [Startup] tab of the [Option] dialog box. [ISIS driver] Mark the [On] checkbox under [Multifeed Recovery] and set [Auto-cancel Timer] to 0 or any value (minutes) on the [Paper Handling] tab of the [Properties for Fujitsu fi-6140...] dialog box. file:///D|/Documents%20and%20Settings/scanner/Desktop/Lynx3/06/contents/EN/03/c03_18_01.htm (4 of 7)9/28/2007 2:39:17 PM

Section	Page
Local Disk	1
6.3 Remedying Typical Troubles	168
6.3 Remedying Typical Troubles	169
6.4 Items to Check Before Contacting the Dealer Where You Bought the Scanner	186
6.5 Checking Labels on the Scanner	189
Chapter 7 ADF AND PAPER SPECIFICATION	190
7.1 Document Size	191
7.2 Document Quality	192
7.3 Maximum Document Loading Capacity	195
7.4 Area Not to be Perforated	196
7.5 Multifeed Detection Conditions	197
Chapter 8 SCANNER SETTINGS	199
8.1 Scanner Settings	200
8.2 Power Saving Setting	205
8.3 Offset/Scan Scale	206
8.4 Multifeed Detection	208
8.5 Page Edge Filler	214
8.6 Dropout Color	216
8.7 Pre-Pick	218
8.8 Intelligent Multifeed Setting	220
8.9 Paper Feeding Retry Times	222
8.10 Life Counter Setting	223
8.11 Timeout for Manual Feeding	225
8.12 Power ON/OFF Control Setting	227
8.13 Paper Protection Setting	229
8.14 Paper Protection Detection Level Setting	231
Chapter 9 SCANNER SPECIFICATION	233
9.1 Basic Specifications	234
9.2 Installation Specifications	236
9.3 External Dimensions	237
APPENDIX 1 Before Using the [Scan] or [Send to] Button	238

Match case Limit results 1 per page

3.18 Not Detecting Multifeed for Fixed Format

●

Intelligent Multifeed Function

Select one of three modes described above.

●

Clear overlap pattern

If this checkbox is marked, the remembered length and location of glued paper (overlap pattern) are deleted

from memory. The overlap pattern is also deleted from memory if you change the Intelligent Multifeed Function

mode.

Before Using This Function

Configure the following settings before using this function:

When the TWAIN driver is used; select [Use Memory on Scanner] or [Use both Memory] as [Cache

Mode] on the [Job/Cache] tab of the [Option] dialog box.

Without this step, you cannot continue scanning after a multifeed error.

When the ISIS or the TWAIN driver is used; if you want to start scanning by using the [Scan]

button after a multifeed error, configure the driver settings as described below.

[TWAIN driver]

Mark the [Enable Scanner Panel] and [Enable [Scan] Button] checkboxes on the [Startup] tab of the [Option] dialog

box.

[ISIS driver]

Mark the [On] checkbox under [Multifeed Recovery] and set [Auto-cancel Timer] to 0 or any value (minutes) on the

[Paper Handling] tab of the [Properties for Fujitsu fi-6140...] dialog box.

file:///D|/Documents%20and%20Settings/scanner/Desktop/Lynx3/06/contents/EN/03/c03_18_01.htm (4 of 7)9/28/2007 2:39:17 PM