Home » Fujitsu Manuals » Scanners » Fujitsu 6240 » Manual Viewer

Fujitsu 6240 Operating Guide - Page 208

Multifeed Detection, Start up the Software Operation Panel.

UPC - 097564307270

Add to My Manuals
Save this manual to your list of manuals

Page 208 highlights

8.4 Multifeed Detection fi-6140 / fi-6240 Image Scanner Operator's Guide TROUBLESHOOTING CONTENTS MAP TOP 8.4 Multifeed Detection "Multifeed" is a feeding error that occurs when two or more sheets in the ADF paper chute are fed simultaneously into the scanner. If you continue scanning document without knowing this multifeed error, you could skip some of important data while scanning the document. The Multifeed Detection function this scanner provides can prevent such troubles. With the Multifeed Detection, the scanner indicates a message and halts the scanning immediately when a multifeed is detected. (Note that the Multifeed Detection is not available for the range about 30 mm from the leading edge of document.) Configure the settings for the Multifeed Detection as follows. 1. Start up the Software Operation Panel. See Section "8.1 Scanner Settings." 2. Select [Device Setting 2] from the left side list in the window, and select [Multifeed] from its lower level. file:///D|/Documents%20and%20Settings/scanner/Desktop/Lynx3/06/contents/EN/08/c08_04_01.htm (1 of 6)9/28/2007 2:38:53 PM

Section	Page
Local Disk	1
6.3 Remedying Typical Troubles	168
6.3 Remedying Typical Troubles	169
6.4 Items to Check Before Contacting the Dealer Where You Bought the Scanner	186
6.5 Checking Labels on the Scanner	189
Chapter 7 ADF AND PAPER SPECIFICATION	190
7.1 Document Size	191
7.2 Document Quality	192
7.3 Maximum Document Loading Capacity	195
7.4 Area Not to be Perforated	196
7.5 Multifeed Detection Conditions	197
Chapter 8 SCANNER SETTINGS	199
8.1 Scanner Settings	200
8.2 Power Saving Setting	205
8.3 Offset/Scan Scale	206
8.4 Multifeed Detection	208
8.5 Page Edge Filler	214
8.6 Dropout Color	216
8.7 Pre-Pick	218
8.8 Intelligent Multifeed Setting	220
8.9 Paper Feeding Retry Times	222
8.10 Life Counter Setting	223
8.11 Timeout for Manual Feeding	225
8.12 Power ON/OFF Control Setting	227
8.13 Paper Protection Setting	229
8.14 Paper Protection Detection Level Setting	231
Chapter 9 SCANNER SPECIFICATION	233
9.1 Basic Specifications	234
9.2 Installation Specifications	236
9.3 External Dimensions	237
APPENDIX 1 Before Using the [Scan] or [Send to] Button	238

Match case Limit results 1 per page

8.4 Multifeed Detection

fi-6140 / fi-6240 Image Scanner Operator's Guide

TROUBLESHOOTING

CONTENTS MAP

TOP

8.4 Multifeed Detection

"Multifeed" is a feeding error that occurs when two or more sheets in the ADF paper chute are fed simultaneously into the

scanner.

If you continue scanning document without knowing this multifeed error, you could skip some of important data while scanning

the document.

The Multifeed Detection function this scanner provides can prevent such troubles.

With the Multifeed Detection, the scanner indicates a message and halts the scanning immediately when a multifeed is detected.

(Note that the Multifeed Detection is not available for the range about 30 mm from the leading edge of document.)

Configure the settings for the Multifeed Detection as follows.

Start up the Software Operation Panel.

See Section "

8.1 Scanner Settings.

Select [Device Setting 2] from the left side list in the window, and select [Multifeed] from its lower

level.

file:///D|/Documents%20and%20Settings/scanner/Desktop/Lynx3/06/contents/EN/08/c08_04_01.htm (1 of 6)9/28/2007 2:38:53 PM