HP 6120XG HP ProCurve Series 6120 Blade Switches Multicast and Routing Guide - Page 31

IGMP Operating Features, Basic Operation, Enhancements

Get HP 6120XG PDF manuals and user guides View all HP 6120XG manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

Multimedia Traffic Control with IP Multicast (IGMP) IGMP General Operation and Features IGMP Operating Features Basic Operation In the factory default configuration, IGMP is disabled. To enable IGMP ■ If multiple VLANs are not configured, you configure IGMP on the default VLAN (DEFAULT_VLAN; VID = 1). ■ If multiple VLANs are configured, you configure IGMP on a per-VLAN basis for every VLAN where this feature is to be used. Enhancements With the CLI, you can configure these additional options: ■ Forward with High Priority. Disabling this parameter (the default) causes the switch or VLAN to process IP multicast traffic, along with other traffic, in the order received (usually, normal priority). Enabling this parameter causes the switch or VLAN to give a higher priority to IP multicast traffic than to other traffic. ■ Auto/Blocked/Forward: You can use the console to configure individual ports to any of the following states: • Auto (the default): Causes the switch to interpret IGMP packets and to filter IP multicast traffic based on the IGMP packet information for ports belonging to a multicast group. This means that IGMP traffic will be forwarded on a specific port only if an IGMP host or multicast router is connected to the port. • Blocked: Causes the switch to drop all IGMP transmissions received from a specific port and to block all outgoing IP Multicast packets for that port. This has the effect of preventing IGMP traffic from moving through specific ports. • Forward: Causes the switch to forward all IGMP and IP multicast transmissions through the port. ■ Operation With or Without IP Addressing: This feature helps to conserve IP addresses by enabling IGMP to run on VLANs that do not have an IP address. See "Operation With or Without IP Addressing" on page 2-13. ■ Querier Capability: The switch performs this function for IGMP on VLANs having an IP address when there is no other device in the VLAN acting as querier. See "Using the Switch as Querier" on page 2-18. 2-5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
Multimedia Traffic Control with IP Multicast (IGMP)
IGMP General Operation and Features
IGMP Operating Features
Basic Operation
In the factory default configuration, IGMP is disabled. To enable IGMP
■
If multiple VLANs are not configured, you configure IGMP on the default
VLAN (DEFAULT_VLAN; VID = 1).
■
If multiple VLANs are configured, you configure IGMP on a per-VLAN
basis for every VLAN where this feature is to be used.
Enhancements
With the CLI, you can configure these additional options:
■
Forward with High Priority.
Disabling this parameter (the default)
causes the switch or VLAN to process IP multicast traffic, along with other
traffic, in the order received (usually, normal priority). Enabling this
parameter causes the switch or VLAN to give a higher priority to IP
multicast traffic than to other traffic.
■
Auto/Blocked/Forward:
You can use the console to configure individual
ports to any of the following states:
•
Auto
(the default): Causes the switch to interpret IGMP packets and
to filter IP multicast traffic based on the IGMP packet information for
ports belonging to a multicast group. This means that IGMP traffic
will be forwarded on a specific port only if an IGMP host or multicast
router is connected to the port.
•
Blocked:
Causes the switch to drop all IGMP transmissions received
from a specific port and to block all outgoing IP Multicast packets for
that port. This has the effect of preventing IGMP traffic from moving
through specific ports.
•
Forward:
Causes the switch to forward all IGMP and IP multicast
transmissions through the port.
■
Operation With or Without IP Addressing:
This feature helps to
conserve IP addresses by enabling IGMP to run on VLANs that do not have
an IP address. See “Operation With or Without IP Addressing” on page
2-13.
■
Querier Capability:
The switch performs this function for IGMP on
VLANs having an IP address when there is no other device in the VLAN
acting as querier. See “Using the Switch as Querier” on page 2-18.
2-5