HP Color LaserJet Managed MFP E77822-E77830 On-Site Installation Guide - Page 83

Install the DCF on the HP Color LaserJet MFP E77822, E77825, E77830

Get HP Color LaserJet Managed MFP E77822-E77830 PDF manuals and user guides View all HP Color LaserJet Managed MFP E77822-E77830 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 83 highlights

Table 8-1 Delivery and installation checklist (continued) ❑ Shake the toner cartridge to distribute the toner. ❑ Open the front door and install the toner cartridge. ❑ Push IN on latches on each side to remove the TCU (toner collection unit). ❑ Open the right door. NOTE: This step is required to retract the interlock at the imaging unit opening. ❑ Unpack the imaging unit. ❑ Remove the white protective cover. CAUTION: Do not touch the green surface of the drum unit. ❑ Pull OUT to remove the orange charge roller shipping lock. ❑ Remove the plug and the tape from the imaging unit vent area. ❑ Pull straight OUT to remove the seal at the front of the imaging unit. ❑ Hold the imaging unit with one hand on the bottom and the other hand on the gray handle at the front of the imaging unit. ❑ Align the bottom of the imaging unit to the bottom of the opening and slide the imaging unit into the device. ❑ Push IN while installing the first screw at the top of the imaging unit. ❑ Install the second screw at the top of the imaging unit. ❑ Connect the imaging unit cable to the front of the MFP. ❑ Route the cable inside the channel at the front of the MFP. ❑ Close the right door. ❑ Install the TCU. ❑ Remove the protective film from the logo on the front door. ❑ Apply the tray number labels. ❑ Install the stabilizer blocks. NOTE: Not required if an external finisher is attached to the device. ❑ Perform Late Point Differentiation and Configuration (LPDC). ❑ Apply the "XA3" barcode inside of the front door and nameplate on the front door of the device. ❑ Upgrade the firmware with latest available on hp.com. ❑ Insert a thumb drive with firmware at the connector on the control panel. ❑ Select the following: Support Tools > Maintenance > USB Firmware Upgrade NOTE: All accessories must be attached when upgrading firmware. NOTE: Accessories added later will NOT be upgraded automatically.. Install the DCF on the HP Color LaserJet MFP E77822, E77825, E77830 Click here to view a video on this procedure. CAUTION: The engine assembly is heavy and requires four people to lift. ENWW HP LaserJet MFP E72525, E72530, E72535 with a DCF and HP LaserJet Spacer installation checklist 77

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
Table 8-1
Delivery and installation checklist (continued)
❑
Shake the toner cartridge to distribute the toner.
❑
Open the front door and install the toner cartridge.
❑
Push IN on latches on each side to remove the TCU (toner collection unit).
❑
Open the right door.
NOTE:
This step is required to retract the interlock at the imaging unit opening.
❑
Unpack the imaging unit.
❑
Remove the white protective cover.
CAUTION:
Do not touch the green surface of the drum unit.
❑
Pull OUT to remove the orange charge roller shipping lock.
❑
Remove the plug and the tape from the imaging unit vent area.
❑
Pull straight OUT to remove the seal at the front of the imaging unit.
❑
Hold the imaging unit with one hand on the bottom and the other hand on the gray handle at the front of the imaging unit.
❑
Align the bottom of the imaging unit to the bottom of the opening and slide the imaging unit into the device.
❑
Push IN while installing the first screw at the top of the imaging unit.
❑
Install the second screw at the top of the imaging unit.
❑
Connect the imaging unit cable to the front of the MFP.
❑
Route the cable inside the channel at the front of the MFP.
❑
Close the right door.
❑
Install the TCU.
❑
Remove the protective film from the logo on the front door.
❑
Apply the tray number labels.
❑
Install the stabilizer blocks.
NOTE:
Not required if an external finisher is attached to the device.
❑
Perform Late Point Differentiation and Configuration (LPDC).
❑
Apply the “XA3” barcode inside of the front door and nameplate on the front door of the device.
❑
Upgrade the firmware with latest available on hp.com.
❑
Insert a thumb drive with firmware at the connector on the control panel.
❑
Select the following: Support Tools > Maintenance > USB Firmware Upgrade
NOTE:
All accessories must be attached when upgrading firmware.
NOTE:
Accessories added later will NOT be upgraded automatically..
Install the DCF on the HP Color LaserJet MFP E77822, E77825, E77830
Click here to view a video on this procedure.
CAUTION:
The engine assembly is heavy and requires four people to lift.
ENWW
HP LaserJet MFP E72525, E72530, E72535 with a DCF and HP LaserJet Spacer installation checklist
77