HP Color LaserJet Managed MFP E77822-E77830 On-Site Installation Guide - Page 94

HP LaserJet Stapler/Stacker Finisher

Get HP Color LaserJet Managed MFP E77822-E77830 PDF manuals and user guides View all HP Color LaserJet Managed MFP E77822-E77830 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 94 highlights

Table 8-9 On-site final setup booklet maker finisher with punch (continued) ❑ Align the brackets on the engine to the holes on the finisher and roll the finisher against the engine. ❑ Push the locking rail in and install one screw to secure the finisher to the engine. NOTE: If the locking rail won't slide in easily, adjust the casters on the finisher to change the height. NOTE: Check the vertical gap between the finisher and the engine. Adjust the casters for an equal gap from top to bottom. NOTE: Remove the finisher from the engine if the MFP needs to be moved anything more than a very short distance. HP LaserJet Stapler/Stacker Finisher Click here to view a video of this procedure. Please review the LaserJet A3 video for a complete understanding of the installation of each device. Use these checklists as a reminder of the steps demonstrated in the videos. Table 8-10 On-site final setup stapler/stacker ❑ Power down the MFP. ❑ Unpack finisher, bridge and attachment hardware. ❑ Remove packing foam and tape from the bridge. NOTE: E7 engines require the 2nd exit to be installed first. NOTE: E7 mono engines require a spacer to be installed before attaching a finishing option. NOTE: On the engine, remove the bin full actuator, paper settling arms and face down bin. ❑ Install the bridge on the engine. Secure with one screw. ❑ Remove the packing foam and tape from the finisher. ❑ Open the top cover on finisher and remove the foam and tape inside the paper path. ❑ Open front door on finisher and remove packing foam and tape inside door.. ❑ Remove the stapler shipping lock screw and label. ❑ Rotate the green wheel to the left until the spring loaded white tab is exposed under the stapler. ❑ Rotate the green wheel to the right until the stapler moves back to the front position and stops. ❑ While holding the green wheel, insert the staple cartridge holder into the stapler. ❑ Hang the lower tray support brackets on the horizontal bracket on the output side of the finisher. ❑ Secure each bracket with one screw. ❑ Note the alignment pins on the bottom of the tray and the corresponding holes on the support brackets. ❑ Position the tray over the brackets and push down firmly to seat the pins in the holes. ❑ While holding the tray from above, install four screws to secure the tray to the support brackets. ❑ Note the four tabs. Install the upper tray into the slots. ❑ Install front (F) and the rear (R) and the finisher attachment brackets on the left side of the engine. ❑ Secure with two screws in each bracket. ❑ Peel the cover off the connector near the rear bracket. 88 Chapter 8 Complete installation procedures ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
Table 8-9
On-site final setup booklet maker finisher with punch (continued)
❑
Align the brackets on the engine to the holes on the finisher and roll the finisher against the engine.
❑
Push the locking rail in and install one screw to secure the finisher to the engine.
NOTE:
If the locking rail won’t slide in easily, adjust the casters on the finisher to change the height.
NOTE:
Check the vertical gap between the finisher and the engine. Adjust the casters for an equal gap from top to bottom.
NOTE:
Remove the finisher from the engine if the MFP needs to be moved anything more than a very short distance.
HP LaserJet Stapler/Stacker Finisher
Click here to view a video of this procedure.
Please review the LaserJet A3 video for a complete understanding of the installation of each device. Use these
checklists as a reminder of the steps demonstrated in the videos.
Table 8-10
On-site final setup stapler/stacker
❑
Power down the MFP.
❑
Unpack finisher, bridge and attachment hardware.
❑
Remove packing foam and tape from the bridge.
NOTE:
E7 engines require the 2nd exit to be installed first.
NOTE:
E7 mono engines require a spacer to be installed before attaching a finishing option.
NOTE:
On the engine, remove the bin full actuator, paper settling arms and face down bin.
❑
Install the bridge on the engine. Secure with one screw.
❑
Remove the packing foam and tape from the finisher.
❑
Open the top cover on finisher and remove the foam and tape inside the paper path.
❑
Open front door on finisher and remove packing foam and tape inside door..
❑
Remove the stapler shipping lock screw and label.
❑
Rotate the green wheel to the left until the spring loaded white tab is exposed under the stapler.
❑
Rotate the green wheel to the right until the stapler moves back to the front position and stops.
❑
While holding the green wheel, insert the staple cartridge holder into the stapler.
❑
Hang the lower tray support brackets on the horizontal bracket on the output side of the finisher.
❑
Secure each bracket with one screw.
❑
Note the alignment pins on the bottom of the tray and the corresponding holes on the support brackets.
❑
Position the tray over the brackets and push down firmly to seat the pins in the holes.
❑
While holding the tray from above, install four screws to secure the tray to the support brackets.
❑
Note the four tabs. Install the upper tray into the slots.
❑
Install front (F) and the rear (R) and the finisher attachment brackets on the left side of the engine.
❑
Secure with two screws in each bracket.
❑
Peel the cover off the connector near the rear bracket.
88
Chapter 8
Complete installation procedures
ENWW