HP Color LaserJet Managed MFP E77822-E77830 On-Site Installation Guide - Page 95

HP LaserJet Job Separator, Staples

Get HP Color LaserJet Managed MFP E77822-E77830 PDF manuals and user guides View all HP Color LaserJet Managed MFP E77822-E77830 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 95 highlights

Table 8-10 On-site final setup stapler/stacker (continued) ❑ Position the finisher near the left side of the engine and connect the two cables. ❑ Open the finisher front door and pull out the locking rail until it stops. ❑ Align the brackets on the engine to the holes on the finisher and roll the finisher against the engine. ❑ Push the locking rail in and install one screw to secure the finisher to the engine. NOTE: If the locking rail won't slide in easily, adjust the casters on the finisher to change the height. NOTE: Check the vertical gap between the finisher and the engine. Adjust the casters for an equal gap from top to bottom. NOTE: Remove the finisher from the engine if the MFP needs to be moved anything more than a very short distance. HP LaserJet Job Separator There is no installation video available for this procedure. User this checklist to perform the installation of the Job Separator. NOTE: The Job Separator requires the installation of the optional HP LaserJet 2nd exit. Table 8-11 On-site final setup job separator ❑ Remove the tape which covers the support hole on the back wall under the scanner. ❑ Install the job separator by aligning the tabs on the right side to the holes on the second exit. ❑ Insert the left side table into the hole on the back wall under the scanner. Staples Click here to view a video of this procedure HP LaserJet Inner finisher and Booklet Maker finisher refill staple cartridge product number: Y1G13A. Replace the inner finisher staple cartridge 1. Open the staple cartridge access door. ENWW Finishers 89

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
Table 8-10
On-site final setup stapler/stacker (continued)
❑
Position the finisher near the left side of the engine and connect the two cables.
❑
Open the finisher front door and pull out the locking rail until it stops.
❑
Align the brackets on the engine to the holes on the finisher and roll the finisher against the engine.
❑
Push the locking rail in and install one screw to secure the finisher to the engine.
NOTE:
If the locking rail won’t slide in easily, adjust the casters on the finisher to change the height.
NOTE:
Check the vertical gap between the finisher and the engine. Adjust the casters for an equal gap from top to bottom.
NOTE:
Remove the finisher from the engine if the MFP needs to be moved anything more than a very short distance.
HP LaserJet Job Separator
There is no installation video available for this procedure.
User this checklist to perform the installation of the Job Separator.
NOTE:
The Job Separator requires the installation of the optional HP LaserJet 2nd exit.
Table 8-11
On-site final setup job separator
❑
Remove the tape which covers the support hole on the back wall under the scanner.
❑
Install the job separator by aligning the tabs on the right side to the holes on the second exit.
❑
Insert the left side table into the hole on the back wall under the scanner.
Staples
Click here to view a video of this procedure
HP LaserJet Inner finisher and Booklet Maker finisher refill staple cartridge product number: Y1G13A.
Replace the inner finisher staple cartridge
1.
Open the staple cartridge access door.
ENWW
Finishers
89