HP Color LaserJet Managed MFP E77822-E77830 On-Site Installation Guide - Page 90

Finishers, Install the Inner Finisher on the HP LaserJet MFP E725 and E778 Color products

Get HP Color LaserJet Managed MFP E77822-E77830 PDF manuals and user guides View all HP Color LaserJet Managed MFP E77822-E77830 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 90 highlights

Finishers Install the Inner Finisher on the HP LaserJet MFP E725 and E778 Color products Click here to view a video on this procedure. CAUTION: The engine assembly is heavy and requires four people to lift. Please review the LaserJet A3 videos for a complete understanding of the installation of each device. Use these checklists as a reminder of the steps demonstrated in the videos. NOTE: The following steps are required before installing the inner finisher on an E7 Mono MFP. ● Remove the face down bin. ● Remove the paper setting guides. ● Remove the 1st exit bin full actuator. ● Install the 2nd exit unit. Table 8-7 On-site final setup inner finisher on the HP LaserJet MFP E72525, E72530, E72535 ❑ Unpack the inner finisher and locate the slide rails. NOTE: The plastic "U" shaped bracket is the wavy retainer. It is used when installing the inner finisher on an E8 prodcut. It is NOT used when installing an inner finisher on an E7 product. ❑ Align the slides to the locator pins located on the top of the engine. NOTE: The white plastic end guide faces left. ❑ Use a short (stubby) JIS#2 to install three screws in each slide. NOTE: These are self-taping screws and require downward force to tap the holes. CAUTION: The inner rails have sharp edges. TIP: Slide the inner rails to the right to make the installation of the inner finisher easier. ❑ Position the inner finisher against the back wall of the opening. ❑ Hold level and then push IN to engage the unit in the slides. ❑ Open the front door and release the latch. ❑ Pull the finisher out and then back in to verify it is properly engaged with the slides. ❑ Remove stapler shipping lock label and remove shipping lock screw. ❑ Remove connector cover on left side of MFP. ❑ Connect the inner finisher cable to the MFP. ❑ Locate the output tray. NOTE: The four pins on the bottom of the tray needs to be aligned with the holes on the support brackets. NOTE: Push down firmly to engage the pins into the holes on the brackets. NOTE: Lift the output finger assembly when installing tray. 84 Chapter 8 Complete installation procedures ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
Finishers
Install the Inner Finisher on the HP LaserJet MFP E725 and E778 Color products
Click here to view a video on this procedure.
CAUTION:
The engine assembly is heavy and requires four people to lift.
Please review the LaserJet A3 videos for a complete understanding of the installation of each device. Use these
checklists as a reminder of the steps demonstrated in the videos.
NOTE:
The following steps are required before installing the inner finisher on an E7 Mono MFP.
●
Remove the face down bin.
●
Remove the paper setting guides.
●
Remove the 1st exit bin full actuator.
●
Install the 2nd exit unit.
Table 8-7
On-site final setup inner finisher on the HP LaserJet MFP E72525, E72530, E72535
❑
Unpack the inner finisher and locate the slide rails.
NOTE:
The plastic “U” shaped bracket is the wavy retainer. It is used when installing the inner finisher on an E8 prodcut. It is NOT
used when installing an inner finisher on an E7 product.
❑
Align the slides to the locator pins located on the top of the engine.
NOTE:
The white plastic end guide faces left.
❑
Use a short (stubby) JIS#2 to install three screws in each slide.
NOTE:
These are self-taping screws and require downward force to tap the holes.
CAUTION:
The inner rails have sharp edges.
TIP:
Slide the inner rails to the right to make the installation of the inner finisher easier.
❑
Position the inner finisher against the back wall of the opening.
❑
Hold level and then push IN to engage the unit in the slides.
❑
Open the front door and release the latch.
❑
Pull the finisher out and then back in to verify it is properly engaged with the slides.
❑
Remove stapler shipping lock label and remove shipping lock screw.
❑
Remove connector cover on left side of MFP.
❑
Connect the inner finisher cable to the MFP.
❑
Locate the output tray.
NOTE:
The four pins on the bottom of the tray needs to be aligned with the holes on the support brackets.
NOTE:
Push down firmly to engage the pins into the holes on the brackets.
NOTE:
Lift the output finger assembly when installing tray.
84
Chapter 8
Complete installation procedures
ENWW