HP Color LaserJet Managed MFP E77822-E77830 On-Site Installation Guide - Page 92

HP LaserJet Booklet Maker Finisher with punch, Install the spacer and DCF/Cabinet HP LaserJet

Get HP Color LaserJet Managed MFP E77822-E77830 PDF manuals and user guides View all HP Color LaserJet Managed MFP E77822-E77830 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 92 highlights

Table 8-8 On-site final setup inner finisher punch (continued) ❑ Place the inner finisher front side down on a table. ❑ Insert the hinge pin - verify cables are located to the left of the pin. ❑ Replace the e-clip. ❑ Connect the two cables. ❑ Replace the rear cover. TIP: Locate the three tabs along the top of the cover and engage with corresponding holes on the frame. ❑ Snap the cover back down in the lower corner. ❑ Reinstall three screws. ❑ Turn the finisher back to its normal orientation. ❑ Open the inner finisher front door. ❑ Unlatch and open the inner punch. ❑ Use a piece of blue tape to hold the latch in the open position. ❑ Place the black washer on the pin. ❑ Reinstall the e-clip on the pin. ❑ Peel off the backing and install the new mylar over the opening. ❑ Remove the dummy door and install the punch waste bin. ❑ Remove the blue tape and close the inner finisher. HP LaserJet Booklet Maker Finisher with punch Click here to view a video of this procedure. NOTE: The HP LaserJet MFP E72525dn/z, E72530dn/z, E72535dn/z models require the spacer to be installed to increase the height of the engine to match the finisher. See the Install the spacer and DCF/Cabinet (HP LaserJet MFP E72525dn/z, E72530dn/z, E72535dn/z) section for instructions. Please review the LaserJet A3 videos for a complete understanding of the installation of each device. Use these checklists as a reminder of the steps demonstrated in the videos. Table 8-9 On-site final setup booklet maker finisher with punch ❑ Power down the MFP. ❑ Unpack finisher, bridge and attachment hardware. NOTE: E7 engines require the 2nd exit to be installed first. NOTE: E7 mono engines require a spacer to be installed before attaching a finishing option. NOTE: On the engine, remove the bin full actuator, paper settling arms and face down bin. ❑ Remove packing foam and tape from the finisher. ❑ Open the top cover and remove the foam and tape inside the paper path. ❑ Locate and remove the shipping bracket for the booklet maker. Use one screw to store the bracket on the frame. 86 Chapter 8 Complete installation procedures ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
Table 8-8
On-site final setup inner finisher punch (continued)
❑
Place the inner finisher front side down on a table.
❑
Insert the hinge pin – verify cables are located to the left of the pin.
❑
Replace the e-clip.
❑
Connect the two cables.
❑
Replace the rear cover.
TIP:
Locate the three tabs along the top of the cover and engage with corresponding holes on the frame.
❑
Snap the cover back down in the lower corner.
❑
Reinstall three screws.
❑
Turn the finisher back to its normal orientation.
❑
Open the inner finisher front door.
❑
Unlatch and open the inner punch.
❑
Use a piece of blue tape to hold the latch in the open position.
❑
Place the black washer on the pin.
❑
Reinstall the e-clip on the pin.
❑
Peel off the backing and install the new mylar over the opening.
❑
Remove the dummy door and install the punch waste bin.
❑
Remove the blue tape and close the inner finisher.
HP LaserJet Booklet Maker Finisher with punch
Click here to view a video of this procedure.
NOTE:
The HP LaserJet MFP E72525dn/z, E72530dn/z, E72535dn/z models require the spacer to be installed
to increase the height of the engine to match the finisher. See the
Install the spacer and DCF/Cabinet (HP LaserJet
MFP E72525dn/z, E72530dn/z, E72535dn/z)
section for instructions.
Please review the LaserJet A3 videos for a complete understanding of the installation of each device. Use these
checklists as a reminder of the steps demonstrated in the videos.
Table 8-9
On-site final setup booklet maker finisher with punch
❑
Power down the MFP.
❑
Unpack finisher, bridge and attachment hardware.
NOTE:
E7 engines require the 2nd exit to be installed first.
NOTE:
E7 mono engines require a spacer to be installed before attaching a finishing option.
NOTE:
On the engine, remove the bin full actuator, paper settling arms and face down bin.
❑
Remove packing foam and tape from the finisher.
❑
Open the top cover and remove the foam and tape inside the paper path.
❑
Locate and remove the shipping bracket for the booklet maker. Use one screw to store the bracket on the frame.
86
Chapter 8
Complete installation procedures
ENWW