HP Color LaserJet Managed MFP E77822-E77830 On-Site Installation Guide - Page 91

HP LaserJet Inner finisher, Install the Inner HP LaserJet Punch

Get HP Color LaserJet Managed MFP E77822-E77830 PDF manuals and user guides View all HP Color LaserJet Managed MFP E77822-E77830 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 91 highlights

Table 8-7 On-site final setup inner finisher on the HP LaserJet MFP E72525, E72530, E72535 (continued) ❑ Install the tray on the support brackets and push down firmly to seat the pins in the holes. ❑ Hold the tray from above while installing the self-tapping screws from below. HP LaserJet Inner finisher Install the Inner HP LaserJet Punch Click here to view a video of this procedure. CAUTION: The engine assembly is heavy and requires four people to lift. Please review the LaserJet A3 videos for a complete understanding of the installation of each device. Use these checklist as a reminder of the steps demonstrated in the videos. NOTE: The inner punch must be purchased separately and is installed in the inner finisher. This is a checklists for installing the inner punch into a new inner finisher. Table 8-8 On-site final setup inner finisher punch ❑ Unpack the inner finisher and remove all the blue packing tape. ❑ Open the inner finisher front door. ❑ Unlatch and open the jam access area (also know as the dummy punch). ❑ Remove and discard the mylar surrounding the latch handle. ❑ Use a piece of blue tape to hold the latch in the open position. ❑ Locate and remove the e-clip and plastic washer just behind the lever. ❑ Remove the blue tape, close the dummy punch and close the front door. ❑ Place the finisher front side down on a table. ❑ Locate and remove three screws on the rear cover. ❑ Use a flat blade screwdriver to release the cover tab located at the lower rear corner near the cable entrance and lift the cover slightly. ❑ Now pull along the top edge to release three tabs and remove the cover. ❑ Locate the hinge pin at the rear of the dummy punch. ❑ Remove the e-clip at the bottom of the hinge pin and remove the hinge pin. ❑ Disconnect the cable. ❑ Turn the finisher back to its normal orientation.. ❑ Open the front cover. ❑ Open the dummy punch. ❑ Pull forward to remove the dummy punch from the inner finisher. ❑ Unpack the inner punch. ❑ Position the inner punch on the inner finisher and slide the cables through the chassis at the rear. ❑ Close the inner punch and the front cover. ENWW Finishers 85

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
Table 8-7
On-site final setup inner finisher on the HP LaserJet MFP E72525, E72530, E72535 (continued)
❑
Install the tray on the support brackets and push down firmly to seat the pins in the holes.
❑
Hold the tray from above while installing the self-tapping screws from below.
HP LaserJet Inner finisher
Install the Inner HP LaserJet Punch
Click here to view a video of this procedure.
CAUTION:
The engine assembly is heavy and requires four people to lift.
Please review the LaserJet A3 videos for a complete understanding of the installation of each device. Use these
checklist as a reminder of the steps demonstrated in the videos.
NOTE:
The inner punch must be purchased separately and is installed in the inner finisher. This is a checklists
for installing the inner punch into a new inner finisher.
Table 8-8
On-site final setup inner finisher punch
❑
Unpack the inner finisher and remove all the blue packing tape.
❑
Open the inner finisher front door.
❑
Unlatch and open the jam access area (also know as the dummy punch).
❑
Remove and discard the mylar surrounding the latch handle.
❑
Use a piece of blue tape to hold the latch in the open position.
❑
Locate and remove the e-clip and plastic washer just behind the lever.
❑
Remove the blue tape, close the dummy punch and close the front door.
❑
Place the finisher front side down on a table.
❑
Locate and remove three screws on the rear cover.
❑
Use a flat blade screwdriver to release the cover tab located at the lower rear corner near the cable entrance and lift the cover
slightly.
❑
Now pull along the top edge to release three tabs and remove the cover.
❑
Locate the hinge pin at the rear of the dummy punch.
❑
Remove the e-clip at the bottom of the hinge pin and remove the hinge pin.
❑
Disconnect the cable.
❑
Turn the finisher back to its normal orientation..
❑
Open the front cover.
❑
Open the dummy punch.
❑
Pull forward to remove the dummy punch from the inner finisher.
❑
Unpack the inner punch.
❑
Position the inner punch on the inner finisher and slide the cables through the chassis at the rear.
❑
Close the inner punch and the front cover.
ENWW
Finishers
85