HP Dl180 ProLiant DL180 Generation 5 Server Maintenance and Service Guide - Page 27

Pre-installation procedure, Post-installation instructions, Server warnings and cautions

Get HP Dl180 - G6 E5504 2X2gb 4Lff Svr PDF manuals and user guides
UPC - 883585990917
View all HP Dl180 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

• Make sure that you are always properly grounded (earthed) when touching a static-sensitive component or assembly. • Avoid touching pins, leads, or circuitry. • Always place drives with the Printed Circuit Board (PCB) assembly-side down. • Use conductive field service tools. Pre-installation procedure Perform the steps below before you open the server or before you remove or replace any component. WARNING: Failure to properly turn off the server before you open the server or before you start installing/removing components may cause serious damage as well as bodily harm. 1. Turn off the server and all the peripherals connected to it. 2. Unplug all cables from the power outlets to avoid exposure to high energy levels that may cause burns when parts are short-circuited by metal objects such as tools or jewelry. If necessary, label each one to expedite reassembly. 3. Disconnect telecommunication cables to avoid exposure to shock hazard from ringing voltages. 4. If server is installed in a rack, remove server and place it on a flat surface. 5. Remove the top cover according to the instructions described in the System covers section in this chapter. 6. Remove the top middle cover according to the instructions described in the System covers section in this chapter. 7. Follow the ESD precautions listed previously in this chapter when handling a server component. IMPORTANT: To streamline the configuration process, read through the entire installation/removal procedure first and make sure you understand the steps before you begin. Post-installation instructions Observe the following items after installing or removing a server component: 1. Be sure all components are installed according to the described step-by-step instructions. 2. Reinstall the rear cage, air baffle, peripherals, and system cables that you have removed. 3. Reinstall the top cover. 4. Reinstall the top middle cover. 5. Reinstall server into rack. 6. Connect all external cables and the AC power cord to the system. 7. Press the power button on the front panel to turn on the server. Server warnings and cautions Before installing a server, be sure that you understand the following warnings and cautions. WARNING: To reduce the risk of electric shock or damage to the equipment: • Do not disable the power cord grounding plug. The grounding plug is an important safety feature. • Plug the power cord into a grounded (earthed) electrical outlet that is easily accessible at all times. Removal and replacement procedures 27

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
Removal and replacement procedures
27
•
Make sure that you are always properly grounded (earthed) when touching a static-sensitive
component or assembly.
•
Avoid touching pins, leads, or circuitry.
•
Always place drives with the Printed Circuit Board (PCB) assembly-side down.
•
Use conductive field service tools.
Pre-installation procedure
Perform the steps below before you open the server or before you remove or replace any component.
WARNING:
Failure to properly turn off the server before you open the server or before you start
installing/removing components may cause serious damage as well as bodily harm.
1.
Turn off the server and all the peripherals connected to it.
2.
Unplug all cables from the power outlets to avoid exposure to high energy levels that may cause
burns when parts are short-circuited by metal objects such as tools or jewelry.
If necessary, label each one to expedite reassembly.
3.
Disconnect telecommunication cables to avoid exposure to shock hazard from ringing voltages.
4.
If server is installed in a rack, remove server and place it on a flat surface.
5.
Remove the top cover according to the instructions described in the System covers section in this
chapter.
6.
Remove the top middle cover according to the instructions described in the System covers section
in this chapter.
7.
Follow the ESD precautions listed previously in this chapter when handling a server component.
IMPORTANT:
To streamline the configuration process, read through the entire installation/removal
procedure first and make sure you understand the steps before you begin.
Post-installation instructions
Observe the following items after installing or removing a server component:
1.
Be sure all components are installed according to the described step-by-step instructions.
2.
Reinstall the rear cage, air baffle, peripherals, and system cables that you have removed.
3.
Reinstall the top cover.
4.
Reinstall the top middle cover.
5.
Reinstall server into rack.
6.
Connect all external cables and the AC power cord to the system.
7.
Press the power button on the front panel to turn on the server.
Server warnings and cautions
Before installing a server, be sure that you understand the following warnings and cautions.
WARNING:
To reduce the risk of electric shock or damage to the equipment:
•
Do not disable the power cord grounding plug. The grounding plug is an important safety feature.
•
Plug the power cord into a grounded (earthed) electrical outlet that is easily accessible at all times.