HP Dl180 ProLiant DL180 Generation 5 Server Maintenance and Service Guide - Page 67

Device number, Connector, To remove the system fan

Get HP Dl180 - G6 E5504 2X2gb 4Lff Svr PDF manuals and user guides
UPC - 883585990917
View all HP Dl180 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 67 highlights

Figure 61 System fan connections Device number Connector System fan 1 J34 on the system board System fan 2 J40 on the system board System fan 3 J22 on the system board System fan 4 J35 on the system board System fans 1 to 3 are for the memory modules and processors, while system fan 4 is for the PCI slots and system chipsets. A new system fan can be installed to allow the server to operate properly in case a default system fan becomes defective. To remove the system fan: 1. Disconnect the fan cable from its corresponding board connector. 2. Release the fan cable from the cable clip securing it to the chassis partition wall. 3. Squeeze the release tab on the system fan to release it from the chassis. 4. Lift the system fan away from the chassis. Removal and replacement procedures 67

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
Removal and replacement procedures
67
Figure 61
System fan connections
Device number
Connector
System fan 1
J34 on the system board
System fan 2
J40 on the system board
System fan 3
J22 on the system board
System fan 4
J35 on the system board
System fans 1 to 3 are for the memory modules and processors, while system fan 4 is for the PCI slots and
system chipsets.
A new system fan can be installed to allow the server to operate properly in case a default system fan
becomes defective.
To remove the system fan:
1.
Disconnect the fan cable from its corresponding board connector.
2.
Release the fan cable from the cable clip securing it to the chassis partition wall.
3.
Squeeze the release tab on the system fan to release it from the chassis.
4.
Lift the system fan away from the chassis.